Ricky116 Posted February 28, 2009 Report Share Posted February 28, 2009 Hmm lets see... Reinstalled winshield wiper valance after a load of detailing oh ya rewelding the hinge that broke sanded and touched up in good ole paint code. 237 i spot puddied the kick panels sanded and painted. They look new again yea!! Quote Link to comment
73dat Posted February 28, 2009 Report Share Posted February 28, 2009 give my L320 a bath,took her for a spin at SoCal meet,last nite...............:cool: Quote Link to comment
ImInked Posted February 28, 2009 Report Share Posted February 28, 2009 Going to sand down the door jambs and get them in primer Quote Link to comment
riverz Posted March 1, 2009 Report Share Posted March 1, 2009 On thursday Iparked it and took the battery out. Will n ot be home for three months off to the desert for me. :D When i get back got to bleed the brakes and replace the power steering line then drive it. Quote Link to comment
yello620 Posted March 1, 2009 Report Share Posted March 1, 2009 I got two new rear tires for my truck today, and two for her car.. Quote Link to comment
Phlebmaster Posted March 1, 2009 Report Share Posted March 1, 2009 I put in a matchbox dizzy and new coil. Took a piece of metal off the exhaust that was rattling all the time. :D May or may not have gone over 100MPH in my 620....hahaha See my project thread. Quote Link to comment
ImInked Posted March 8, 2009 Report Share Posted March 8, 2009 took my tailgate off and removing the paint from the valance i got from sdsurf Quote Link to comment
84TAVeRT Posted March 8, 2009 Report Share Posted March 8, 2009 pulled out the old carpet... vaccumed and installed some new insulation on the floor... gotta get some more... and order that new carpet set... :) tomorrow i will be wiring up a new/used (factory) ignition switch... :) later, Chris Quote Link to comment
whitechef Posted March 8, 2009 Report Share Posted March 8, 2009 I worked my Yokohama mama like a rented mule. You know that little wire that goes between the points and that plastic thingy that goes through the distributer. If the connectors get screwed with enough it loses continuity and and makes you think that every other connection is bad. Sneaky mesmerizing bastard. Quote Link to comment
Phlebmaster Posted March 8, 2009 Report Share Posted March 8, 2009 I rebuilt my hood making a reverse scoop. :D My old hood got trashed after it blew up over my windshield. :( Quote Link to comment
denveratsun Posted March 8, 2009 Report Share Posted March 8, 2009 Installed a white speedo pinion gear and it has helped my MPH display a lot. Rewired my interior light...PO had used tiny little solid core crap. Had to fish the new wire down the "A" pillar...went pretty smooth...nice to have it done! Greased all the zerks in the frontend Also cleaned all the weird grime off of the steering wheel. Where does that stuff even come from? :blink: WTH?? Took hubcaps off again...put them on last week:D Washed the poor thing too. Quote Link to comment
420n620 Posted March 8, 2009 Report Share Posted March 8, 2009 well for the last month I removed the engine twice, put in a new clutch, TO bearing, pilot bearing, resurfaced fly wheel, new rear main crank seal, 6 new soft plugs - twice- :mad:, cleaned and painted engine, new used air pump, 2 new belts, got drunk several times. This week new rear brake shoes maybe fronts if needed, adjusts valves and calibrate carb, test all a.i.r valves. that should keep me busy for a little while.. oh and find out why my rear taillights don't work when I have the head lights on, prob just a bad connecting......... Quote Link to comment
Nissan_Boy85 Posted March 8, 2009 Report Share Posted March 8, 2009 Gave her some new oil, installed a 12V power source for my cell charger, and re-timed her so she hopefully won't diesel. Quote Link to comment
Drummerboy4as Posted March 8, 2009 Report Share Posted March 8, 2009 Installed a 1 1/2" carrier bearing spacer, yay no more vibration!! Filled up my steering box with oil and adjusted the play. No more wandering down the road. I've had a nice "clunking" sound from the pass side front wheel area when turning hard left or right. Pulled the front wheel off and inspected for damage. Found a wore out bushing on the top part of the dog bone. Not gonna fix it though. Planning putting in Hardbody breaks and suspension in a few months. Plus, I ride my bike to work now that the weather is nice :lol: Quote Link to comment
Farmer Joe Posted March 9, 2009 Report Share Posted March 9, 2009 while taking my girlfriend to the bank i noticed that the bolt i had holding my shifter in had almost fallen out. so in the bank parking lot i put the pin and e-clip i got at the junkyard in. its alot tighter now. still need the proper bushings for the shifter though. and i here in a little bit im gonna replace my busted ass clutch master cylinder. then the truck will be tip top! ill take some pictures for my project thread. Quote Link to comment
Nissan_Boy85 Posted March 10, 2009 Report Share Posted March 10, 2009 Sat for a while and tried to figure out why she's dieseling, Drove the living hell outa her, Tore into her old heart for good parts. Quote Link to comment
Guest DatsuNoob Posted March 10, 2009 Report Share Posted March 10, 2009 Got off my lazy ass and started working the dents from my spare pass side door, cut the inside of the door (behind the door card) to get my dolly back there, and got most of it knocked out. Nothing a couple spot welds, some 22ga steel and some good body filler wont fix up. Quote Link to comment
lynchfourtwenty Posted March 11, 2009 Report Share Posted March 11, 2009 had to re ground the dizzy, the wire i had on there gave out, so i cut a nice ground wire off this spare engine harness i have, i didnt have the clip for the end to slip onto the dizzy post so i had to loosen the screw that holds the ground post on an vacume advance on an then stuck the wire under the post thing an tightend the screw.. its a ghetto fix but fuck man it was 11:45 at night, but needless to say it worked.. an boy does that truck run great.. Quote Link to comment
ariascarlos1990 Posted March 11, 2009 Report Share Posted March 11, 2009 installed new clear side markers. :D Quote Link to comment
LAYEDOUTB2K Posted March 11, 2009 Report Share Posted March 11, 2009 slapped a ratsun sticker on it. :D i also got my new generator brushes for my 320. hopefully i can rebuild it and not have to charge my battery every week. though its no biggy when it goes dead, i just use the handcrank. :fu: Quote Link to comment
Bleach Posted March 11, 2009 Report Share Posted March 11, 2009 I put in a new air freshener! :) Quote Link to comment
sdsurf Posted March 11, 2009 Report Share Posted March 11, 2009 took my tailgate off and removing the paint from the valance i got from sdsurf How does it look?:D:D:D Quote Link to comment
ImInked Posted March 14, 2009 Report Share Posted March 14, 2009 How does it look?:D:D:D Its way better than the one i had! I have it in bare metal now and its shiny. Also today i got the driver and passenger fenders down to bare metal and im sanding on the roof maybe tonight Quote Link to comment
808DA6 Posted March 14, 2009 Report Share Posted March 14, 2009 Finished my motor mounts and now the SR sits how it will sit FOREVER! Hahahaha...... .....few more pics in my build thread....... -Brian Quote Link to comment
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.