d.p Posted October 8, 2021 Author Report Share Posted October 8, 2021 Truck is noisy as hell already. If these fuckers will get the truck lower than I’ll deal with the noise. Quote Link to comment
d.p Posted October 9, 2021 Author Report Share Posted October 9, 2021 Also one weird thing about getting my seat redone. I sit way higher now, way higher. I bought a needle scaler from harbor freight and it cleaned them up nicely. Now I need to cur the urethane bushings but not sure on the best way to do that? Tried with a circular saw but didn’t end up with a clean cut. 1 Quote Link to comment
Racer X 69 Posted October 9, 2021 Report Share Posted October 9, 2021 1 hour ago, d.p said: Also one weird thing about getting my seat redone. I sit way higher now, way higher. The old paddling was broken down. When you sat on it there wasn't much support. Th new padding is fresh and stiff, so your butt doesn't sink down as far as it used to. Give it time. Quote Link to comment
mainer311 Posted October 10, 2021 Report Share Posted October 10, 2021 (edited) It’s possible that they tied your springs. They do that so it’s not so bouncy, but it doesn’t allow the springs to sag as much. I always just trim urethane with a razor blade. It doesn’t saw very well. Edited October 10, 2021 by mainer311 Quote Link to comment
d.p Posted October 10, 2021 Author Report Share Posted October 10, 2021 I can just razor blade through a thick bushing? Thought about getting them on a lathe but my engine guy is a pain in the ass to deal with. Quote Link to comment
Stoffregen Motorsports Posted October 10, 2021 Report Share Posted October 10, 2021 Belt sander for the urethane. Or razor blade. You'll find 1001 uses for the needle scaler. It's a fun (but noisy) tool. Quote Link to comment
d.p Posted October 30, 2021 Author Report Share Posted October 30, 2021 Haven’t fucked with the leaf springs although I did get the eyes all cleaned out. But I did get lonely driver crane neck spark plug holders. 3 and 4 wires are too short so i will fix that eventually. 2 Quote Link to comment
d.p Posted October 30, 2021 Author Report Share Posted October 30, 2021 And a better pic of my seat. Seems to have settled a bit and love the look. 5 Quote Link to comment
thisismatt Posted October 30, 2021 Report Share Posted October 30, 2021 Lookin good 1 Quote Link to comment
mainer311 Posted October 30, 2021 Report Share Posted October 30, 2021 Shit, I forgot about your plug wires. Do you want them crimped, or sent in parts so that you can figure out the length? Quote Link to comment
d.p Posted October 30, 2021 Author Report Share Posted October 30, 2021 2 minutes ago, mainer311 said: Shit, I forgot about your plug wires. Do you want them crimped, or sent in parts so that you can figure out the length? Parts is fine. I can crimp them. Quote Link to comment
BrothersGarage Posted October 31, 2021 Report Share Posted October 31, 2021 That new seat looks fantastic. Really brought the interior together. Where are the cup holders? 😉 Engine bay really cleaned up with those LonelyDriver Crane necks. Now to clean that big ole droopy dick off the valve cover lol - only $4 https://www.aliexpress.com/item/1005003432237632.html Quote Link to comment
d.p Posted October 31, 2021 Author Report Share Posted October 31, 2021 The droopy dick breather hose really tied the engine bay together when the wires ran over the cover. I agree now though it looks out of place. Jan 2nd delivery for that filter. K&N from Amazon but doesn’t match as well as that alibaba one. https://www.amazon.com/dp/B009774GCA/ref=cm_sw_r_cp_api_glt_fabc_8P6ZMKJ7BBS481YNGYRB 1 Quote Link to comment
banzai510(hainz) Posted November 2, 2021 Report Share Posted November 2, 2021 I used to do the crimp plug wires but then would pull off and I said Fuck it and got the NGK ones thy never break. Quote Link to comment
mainer311 Posted November 2, 2021 Report Share Posted November 2, 2021 (edited) 13 minutes ago, banzai510(hainz) said: I used to do the crimp plug wires but then would pull off and I said Fuck it and got the NGK ones thy never break. Knowing you, this doesn't surprise me at all. The hood on my 521 always smacks my droopy dick. There's no clearance with the hood prop rod. I guess you could say my rod and my dick don't get along. Edited November 2, 2021 by mainer311 1 Quote Link to comment
d.p Posted November 2, 2021 Author Report Share Posted November 2, 2021 I do notice the crimped ones aren't as tight on the cap side as the NGK ones. But NGK are blue and I don't think they will reach out the timing cover and that will simply not do in my engine bay. Quote Link to comment
mainer311 Posted November 2, 2021 Report Share Posted November 2, 2021 I’ve found that you actually need to burp the air from the boot because they fit so tight. Once the air gets burped out, they suction themselves on. Quote Link to comment
d.p Posted November 2, 2021 Author Report Share Posted November 2, 2021 10 minutes ago, mainer311 said: I’ve found that you actually need to burp the air from the boot because they fit so tight. Once the air gets burped out, they suction themselves on. Say what now? Quote Link to comment
mainer311 Posted November 2, 2021 Report Share Posted November 2, 2021 2 hours ago, d.p said: Say what now? Oops, wrong forum, nevermind. Quote Link to comment
Stoffregen Motorsports Posted November 2, 2021 Report Share Posted November 2, 2021 2 hours ago, mainer311 said: I’ve found that you actually need to burp the air from the boot because they fit so tight. Once the air gets burped out, they suction themselves on. There is a lube for that. Specifically for getting tight fitting boots over spark plugs. The LS crate motors come with a slimy green lube all over the spark plugs. Also, NGK makes black wires. I was a set on a beautiful 240z resto-mod last night on IG. Quote Link to comment
datzenmike Posted November 2, 2021 Report Share Posted November 2, 2021 Four of the six L6 wires can fit around the front of the valve cover. They look nice like that Quote Link to comment
mrbigtanker Posted November 2, 2021 Report Share Posted November 2, 2021 On 10/30/2021 at 1:23 PM, d.p said: Haven’t fucked with the leaf springs although I did get the eyes all cleaned out. But I did get lonely driver crane neck spark plug holders. 3 and 4 wires are too short so i will fix that eventually. Nice radiator hoses. Loosen the top clamp and turn to bottom do its cleaner. And I like the seat, get the panels to match please. Quote Link to comment
d.p Posted November 3, 2021 Author Report Share Posted November 3, 2021 They are OK, the covering on them is falling apart but the clamps are nice. I put it that way because I wanted it to be easy to get off if I had to take the radiator out after I put it all back together. Probably ok to move it now seeing as I have a little under 2k miles on this fucker since swapping the drivetrain. Quote Link to comment
d.p Posted November 6, 2021 Author Report Share Posted November 6, 2021 I think I know why my pan was leaking. The stupid rear main seal needle gaskets were protruding out at the bottom of the block. Therefore the gasket/pan wouldn’t lay flst against the block. so I trimmed those and tried to get them as flat as I could and wondering know if I should use a cork gasket, gasket maker or both? Quote Link to comment
d.p Posted November 6, 2021 Author Report Share Posted November 6, 2021 FWIW I just took out the center link and cross member which was easy peasy lemon squeezy. Quote Link to comment
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.