banzai510(hainz) Posted July 12, 2010 Report Share Posted July 12, 2010 I havent done anything with my Datsuns. all running great.I dont even change the dizzy and rotors in over 6 years. I dont know why people have proplems with their Datsun????????? Quote Link to comment
hang_510 Posted July 12, 2010 Report Share Posted July 12, 2010 500 mi valve adjustment, lookin good :cool: re-did the fuel delivery from the pump, tweaked on the carbs, finally idles nicely. once i get the sych tool back, it should make it past 7000 :) & another 100mi 'test drive' in the cyns too :w00t: the R CO are such an improvement! Quote Link to comment
Cookapoop Posted July 13, 2010 Report Share Posted July 13, 2010 I sat in my 510 today and made vroom vroom noises with my mouth while turning the wheel back and fourth! Quote Link to comment
dennis Posted July 13, 2010 Report Share Posted July 13, 2010 Tried pulling off the intake and exhaust manifolds only to break 2 bolts. Then my neighbor decided to talk to me for 25 min so I had to stop working on it. Quote Link to comment
71dime Posted July 14, 2010 Report Share Posted July 14, 2010 i didnt do anything once again i did window shop on the net fort some wheels though Quote Link to comment
ichorid Posted July 14, 2010 Report Share Posted July 14, 2010 http://yfrog.com/3mb3vj 2.5 inch from the down pipe to a 3" muffler. And today a new windshield is getting put in. Quote Link to comment
wicked_wagon Posted July 14, 2010 Report Share Posted July 14, 2010 pictures from the last weekend Change the Wheels and also change the carpet from the trunk and i also change the rubber of the trunk well a picture says more than words Im working on the Seat's too. Saludos! Quote Link to comment
hang_510 Posted July 14, 2010 Report Share Posted July 14, 2010 sped past a cop, who i looked at looking at me :blink: he just :) and exited :o :hyper: Tried pulling off the intake and exhaust manifolds only to break 2 bolts. try loosening them first next time. Quote Link to comment
71dime Posted July 16, 2010 Report Share Posted July 16, 2010 i just got done cleanin the garage tomorrow im gonna pull the rear sub and disassemble it to get it to the powdercoater and run all new fuel lines while its outa my way. Quote Link to comment
71dime Posted July 17, 2010 Report Share Posted July 17, 2010 i pulled the rear sub out and made my new fuel lines Quote Link to comment
dennis Posted July 17, 2010 Report Share Posted July 17, 2010 ordered more parts and threw the battery charger on it. Quote Link to comment
silverdime Posted July 17, 2010 Report Share Posted July 17, 2010 I got my new orange 510 running!!!!!!! Quote Link to comment
freekwonder Posted July 17, 2010 Report Share Posted July 17, 2010 Adjusted clutch pedal so my clutch actually disengages now, and changed the oil. Quote Link to comment
Spades Posted July 20, 2010 Report Share Posted July 20, 2010 I finished putting this in my 510.... Quote Link to comment
71dime Posted July 28, 2010 Report Share Posted July 28, 2010 Today was a good day my buddy just happened to be scrapping a 280zx so i picked up the strut assemblies, diff, brake master and some other odds and ends all for free. i also wired in the relays for my ka swap and cleaned the garage again. Quote Link to comment
71dime Posted August 2, 2010 Report Share Posted August 2, 2010 i disassembled the 510 and 280 strut assemblies so i can cut off the perches tomorrow, damn the more i get accomplished on my car the the farther away it gets from bein done. Quote Link to comment
Lovely_Crucial71 Posted August 3, 2010 Report Share Posted August 3, 2010 Me n my dad finished the engine wirering on my 510 goon n hooked up the msd ignition n finally started her for the first time since rebuilding her L18 Quote Link to comment
jefe de jefes Posted August 3, 2010 Report Share Posted August 3, 2010 Put the spare on today. One of the tires was falling apart. Old and dry I guess. Quote Link to comment
Loren Posted August 5, 2010 Report Share Posted August 5, 2010 i re- installed the old gas tank in my "Goon" today. if you've seen any of my posts about my car,you'll know all the trouble i've had with this tank. i had thought it was full of rust, but it was also full of some kid of sealer that hadn't stuck and about a pound and a half of dried mud! i haven't been able to find one just like it, since it only has 1 breather hose. i'm hoping it doesn't leak now that i've cleaned all the crap out of it. Quote Link to comment
robslow Posted August 5, 2010 Report Share Posted August 5, 2010 took rear end apart , new bushings in controll arms. figure out a way to mount crossmember solidly Quote Link to comment
71dime Posted August 11, 2010 Report Share Posted August 11, 2010 pulled rear control arm assemblies apart and attempted to press out the bushings out. What a p.i.t.a. i had to end up meltin the rubber out then cut the inner sleaves with a sawzall, then i had to use the airhammer on them . Quote Link to comment
Laecaon Posted August 11, 2010 Report Share Posted August 11, 2010 Lots of sanding to get ready for paint! My arm is about to fall off. Quote Link to comment
DimePiece Posted August 11, 2010 Report Share Posted August 11, 2010 welded in the rear quarter panel of my 2 door :) now only a little floor board and rocker work! Quote Link to comment
71dime Posted August 15, 2010 Report Share Posted August 15, 2010 I plazma'd the exhaust hole out in the rear sub so i can fit 3" inch through it Quote Link to comment
Lovely_Crucial71 Posted August 15, 2010 Report Share Posted August 15, 2010 put a new dome light in now it actually works n fixd my turn signal switch Quote Link to comment
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.