uberkevin Posted July 16, 2015 Author Report Share Posted July 16, 2015 That's what I get for having two ka-e's. 240sx and hardbody mounts. 1 Quote Link to comment
]2eDeYe Posted July 16, 2015 Report Share Posted July 16, 2015 Interesting. :cool: 1 Quote Link to comment
uberkevin Posted July 19, 2015 Author Report Share Posted July 19, 2015 This is what the dual cam driver side mount looks like Still doesn't look like the mount you posted. 1 Quote Link to comment
uberkevin Posted July 19, 2015 Author Report Share Posted July 19, 2015 Here this looks okay. Blackmarkit mount. 2 Quote Link to comment
hobospyder Posted July 20, 2015 Report Share Posted July 20, 2015 where's the vid of it running? 1 Quote Link to comment
datson4life Posted July 20, 2015 Report Share Posted July 20, 2015 Lots better! Is the oil pan on yet? That's another thing i question, if its same as dual cam, dual cam clears crosmember by alot, and clears centerlink by like an inch 2 Quote Link to comment
uberkevin Posted July 23, 2015 Author Report Share Posted July 23, 2015 Small problem. 720 short 5 speed. Picked it up from wayno. We put a 620 L front case on the front of it. I'm trying to put the ring you see in the photo back around the bearing. After putting the Z case back on As you can see there isn't anything groove so that the ring sits in.. The case is bolted on. 1 Quote Link to comment
bananahamuck Posted July 23, 2015 Report Share Posted July 23, 2015 I assume you tried pulling on the input shaft.. Are you positive you put bearing on facing the correct way? 2 Quote Link to comment
uberkevin Posted July 23, 2015 Author Report Share Posted July 23, 2015 Fixed. I needed to take the case off and put it back on as I hold the input shaft from going down.. It wouldn't just pull up like I thought it should but now that it's on right it moves up and down a little. Like it should right. Haha 2 Quote Link to comment
bilzbobaggins Posted July 23, 2015 Report Share Posted July 23, 2015 Though you would leave the z case on for a ka swap? 1 Quote Link to comment
uberkevin Posted July 23, 2015 Author Report Share Posted July 23, 2015 I'm putting the z case on. I had the L case before for the lz. 1 Quote Link to comment
bilzbobaggins Posted July 24, 2015 Report Share Posted July 24, 2015 Cool. Misread the upper post then. Carry on the good work sir 1 Quote Link to comment
uberkevin Posted July 24, 2015 Author Report Share Posted July 24, 2015 I feel that was more my fault. I worded it odd and didn't say that I had caged to the Z case. But I fixed it just so people won't get confused. Words suck. I suck words. Hahaha Thanks. 2 Quote Link to comment
flatcat19 Posted July 24, 2015 Report Share Posted July 24, 2015 Public schools suck. Blame them. Not the language. 2 Quote Link to comment
uberkevin Posted July 25, 2015 Author Report Share Posted July 25, 2015 Picking up a DE tomorrow.. Quote Link to comment
uberkevin Posted July 25, 2015 Author Report Share Posted July 25, 2015 Plan is get the ka-e running driving as I make sure the DE is okay. Then swapyy swappy! 1 Quote Link to comment
uberkevin Posted July 26, 2015 Author Report Share Posted July 26, 2015 Lost some weight. 4 Quote Link to comment
uberkevin Posted July 26, 2015 Author Report Share Posted July 26, 2015 http://www.frsport.com/Genuine-OEM-Complete-Engine-Gasket-Kit--Set--S13-KA24DE_p_2278.html?gclid=Cj0KEQjw58ytBRDMg-HVn4LuqasBEiQAhPkhumiIx2MFJgrZ5L6WnEcZJVWDe5EDTMUnkAGhmU6miDwaAl8T8P8HAQ And a timing kit. Bearings.. Rings probably too. 1 Quote Link to comment
datson4life Posted July 26, 2015 Report Share Posted July 26, 2015 Janksun just came thru for some s13 engine brackets, and made me realize the s13 and s14 engine brackets differ, i hav. Been using s14 ka engine mount/bracket on the driver side for ka swap, i always thought they were the same, i was wrong...heres the brackets next to each other The one i sent in the prior page was s13 from konigs engine, and all look different than the truck ka mount aswell 4 Quote Link to comment
uberkevin Posted July 26, 2015 Author Report Share Posted July 26, 2015 I thought I'd give this mount off the DE a try. But it doesn't have one. HAHA HAHAHA 1 Quote Link to comment
jrock4224 Posted July 28, 2015 Report Share Posted July 28, 2015 its crooked lol 1 Quote Link to comment
bananahamuck Posted July 28, 2015 Report Share Posted July 28, 2015 Here's a thought for the "master" engine builder ,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,, make one ? 1 Quote Link to comment
EastBay521 Posted July 28, 2015 Report Share Posted July 28, 2015 How much do you want for the L bell housing? I am in need......I also need a z bell housing but thay can wait.feel free to throw in a l16timing cover too.mines stripped 1 Quote Link to comment
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.