VintageRice Posted May 28, 2012 Report Share Posted May 28, 2012 Vintage, use some needle nose pliers and pull the cream colored plastic deal in the middle of the diaphragm out, under that there will be a small spring, then use the needle nose to pull the needle out. Ok, so it just snaps in or is held by tention. I just didn't want to break them. Never know, somethings need to twist, others screw, others just yank harder. (dirty minds stay away) Quote Link to comment
spudly13 Posted May 29, 2012 Report Share Posted May 29, 2012 i know its a very rough sketch, and im sure somewhere on the internet this has been asked before i just cant find it. In my opinion it would work, meybe not the most efficient but im not trying to build an insane motor here. Basically, will the boost flow like that, or would the number one cylinder be getting more air then number 4? (this is what ive been argueing with people about) i personally think that pressure is pressure and if the area has 10 pounds in it and each cylinder draws its intake at different times, then in my head id would all get the same air. but im no rocket scientist. Quote Link to comment
Laecaon Posted May 29, 2012 Report Share Posted May 29, 2012 Basically, this wont work. Pressure will not be equal, mainly because of the way the air flows in. Ever seen a river flow? Seen the eddies? Stuff like that acts up. Quote Link to comment
spudly13 Posted May 29, 2012 Report Share Posted May 29, 2012 like i said i couldnt find any info on the subject, and my only argument would be, why does it work on a dodge cummins motor? those motors are almost three feet long and the intake is right in between the number one and two cylinder with 4 more cylinders behind that..... note to anyone who hasnt seen one of these, the motor goes back into the tunnel a ways Quote Link to comment
Laecaon Posted May 29, 2012 Report Share Posted May 29, 2012 I mean it will work, maybe, but its not optimum. There has been a lot of research over on hybrid Z about this. I dont think cummins cares when that motor rarely sees over 3k rpm. Diesels are different Biggest thing I would be worried about, is certain cylinders running lean. Quote Link to comment
VintageRice Posted May 29, 2012 Report Share Posted May 29, 2012 This person did this. Thats all I know. Quote Link to comment
slingshot532 Posted May 29, 2012 Report Share Posted May 29, 2012 Here is a little update on my Honderp, took this picture at 5:30 this morning hoping to have it running this week if not sooner. Also a picture of the header I built out of my old VW J-tubes off a 1600 dp. :D before anyone says anything about headers, I couldn't use the stock manifold with bike carbs because it was literally pumpkin sized and had a hole in the top to meet up to the stock intake, and since nobody makes headers for these anymore I had to make it myself. (yes it has a 2 port exhaust head with exhaust liners, I don't expect much more then the stock 65hp on this beast but it sure sounds nice) More pics of this car. I worked at a honda shop where they cut two intake manifolds, and welded them dack together so they could put two carbs on. It was painted orange and we called it the "General Li".I don't think it was a cvcc, and if I recall it had a 4 to 1 header. I am interested to see how this set up works. The cvcc motors are a little different, the carbs have a third barrel that is way rich and fills a little cup around the sparkplug. The rest of the mix is way lean and the mix around the plug is used to ignite the rest of the fuel. Quote Link to comment
slingshot532 Posted May 29, 2012 Report Share Posted May 29, 2012 It looked like this with General Lee rims. Quote Link to comment
Ratty260z Posted May 29, 2012 Report Share Posted May 29, 2012 Yup that is basically how cvcc works, the 1200 models had a crossflow head and 4 exhaust ports, also the later then 76 heads had 4 port exhausts as well just non crossflow. The 1200cc can make lots of power and is a cool little engine. I had the carbs on the motor already and the way the CVCC is set up in the manifold is there are small pinky sized ports for the CVCC valves, all I did was cross drill from the 4 main ports into the CVCC ports and I didn't have any problems, I would have liked to get a Canadian Non CVCC head but life doesn't always work that way, Maybe someday. Here is a picture of mine. 1 Quote Link to comment
Drummerboy4as Posted May 29, 2012 Report Share Posted May 29, 2012 That was my first car when I was 16. My dad had bought it new and made me pay him $500 for it. Damn I wish I would've kept it. So friggin cool! Quote Link to comment
Z chopper Posted May 29, 2012 Report Share Posted May 29, 2012 yup datsuns and 1st gen civics Quote Link to comment
slingshot532 Posted May 31, 2012 Report Share Posted May 31, 2012 That is a fun little car!! Quote Link to comment
VintageRice Posted May 31, 2012 Report Share Posted May 31, 2012 BAAAACK TO TOPIC ! ! :) hehe What you've all been waiting for !! ! ! A DRIVE VIDEO ! ! ! Here ya go. 1 Quote Link to comment
Farmer Joe Posted May 31, 2012 Report Share Posted May 31, 2012 it looks fast... cant hear it tho.. any in car camera work done? Quote Link to comment
Laecaon Posted May 31, 2012 Report Share Posted May 31, 2012 I laugh at the Breathe Carolina playing in the background! lols. Otherwise looks like the car runs super well! Quote Link to comment
VintageRice Posted May 31, 2012 Report Share Posted May 31, 2012 I laugh at the Breathe Carolina playing in the background! lols. Otherwise looks like the car runs super well! :D Quote Link to comment
VintageRice Posted May 31, 2012 Report Share Posted May 31, 2012 it looks fast... cant hear it tho.. any in car camera work done? Not yet. Was going to but gopro battery died. Quote Link to comment
datsundash Posted May 31, 2012 Report Share Posted May 31, 2012 16-20 seconds is my favorite! Quote Link to comment
2JZ260z Posted May 31, 2012 Report Share Posted May 31, 2012 Lol, damn non-media people makin' vids. NO GOD DAMN MUSIC! Also, incar and in engine bay woulda been cool! Quote Link to comment
Ratty260z Posted May 31, 2012 Report Share Posted May 31, 2012 Sorry for the Honduh thread jack haha, My intake is getting welded up hopefully tomorrow or the next day, waiting to hear back, maybe I'll make a video once I get it running, I always tried to convince my buddy while he had his built L20b in his 510 wagon to put some motorcycle carbs on but he pussed out and sold the car, plus he owns a fox-body as well and doesn't believe in ITB's like I do, I'm always preaching to my friends on ITB's and ITC's "oh you should put bike carbs or build ITB's for that yadda yadda" The video is awesome but I want to hear some sweet intake sound yo. Quote Link to comment
VintageRice Posted May 31, 2012 Report Share Posted May 31, 2012 Dangit...........u guys are gunna make me pull my hood off again arent you........ Quote Link to comment
slingshot532 Posted May 31, 2012 Report Share Posted May 31, 2012 Dude congrats! It drives nice. :thumbup: What are your jet sizes? I think I scared my self with the a/f meter and started changing to much stuff. Are you still running the stock size pilots? Quote Link to comment
VintageRice Posted May 31, 2012 Report Share Posted May 31, 2012 Yeah, stock idle jets, 4 turns out. Was at 3.5 turns but richened it up some. U scared me into it........lol Mains drilled to aprox 2mm. I used a 5/64th drill bit which is 1.9844mm So with a little wiggle room probably came out around 2mm. Close enough. I did a 1-2 gear WOT pull in the video then shu tthe motor off and rolled to a stop to read the plugs. (ive read this is the way to do it) Plugs looked nice and dark brown. On the rich side I'd say. Sure with aI had a wide band to check it through the entire RPM range but O well. Hot rodders ran carbs for half a century without fancy gauges and computers to tell'em their runnin rich or lean. Why should we!! Quote Link to comment
VintageRice Posted May 31, 2012 Report Share Posted May 31, 2012 BTW, i think I filled the trans to high or something. Doing WOT 1-2 gear, oil started gushing out around the shifter........is that it or other issues?>??? Quote Link to comment
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.