slodat Posted June 5, 2010 Report Share Posted June 5, 2010 I went to look at a cutting torch I found on craigslist and ended up dragging home a Grizzly knee mill instead. I got it unloaded and it is in the position I'd like to set it in. It is currently resting on 1.5" square tubing passing under the fork lift pockets. The tubing is setting on stacks of (3) 2x4s so I could get the pallet jack out from under it. Now comes the fun part - How do I get it down? I don't have anything above it to hook my chain fall to..Thanks in advance for any help!! Quote Link to comment
motavated Posted June 5, 2010 Report Share Posted June 5, 2010 You light the wood on fire... Quote Link to comment
skunk Posted June 5, 2010 Report Share Posted June 5, 2010 if you do it his way plz make a video, :lol: Quote Link to comment
elmerfudpucker Posted June 5, 2010 Report Share Posted June 5, 2010 you will need a long chain, pick a corner, wrap chain around corner, hook chain to truck bumper, and take off! :D Just kidding, one corner at a time and a long crowbar, take one block at a time from each corner till you down on the floor. have fun... Quote Link to comment
skunk Posted June 5, 2010 Report Share Posted June 5, 2010 i got an idea, sounds a bit out there but maybe it could work. so start by cuting the wood so its flush with the mil on the front half. then get a few round pipes (heavy duty) and slowly push the mil on the pipes, the mil should roll like its on a conveyor belt. then just move the wood and push it back. its going to take a few guys but iv done somghing like that with a big ass oven at my old job. (would be even better to cut the wood at an angle so you can get the pipe under the mill a little) Quote Link to comment
Gary Posted June 5, 2010 Report Share Posted June 5, 2010 crowbar/leverage is a sweet idea, just get a mate (or perhaps two) to steady it if you've got some more steel and a welder handy could make a stand for it out of the two bits that are already there, which'll facilitate you moving it in future cool pickup, im jealous :( i want a mill baad Quote Link to comment
slodat Posted June 5, 2010 Author Report Share Posted June 5, 2010 Engine hoist isn't really a safe option I don't think. The mill weighs just at 2000 pounds. I hauled it home in my 620 KC. I removed the head and made two trips. I have a 2 ton chain hoist that I used to put the head back on the column. I don't have a good way to lift it now that it's in place. I'm thinking of using a prybar (long piece of 1.5" square tubing) to lift one side and knock the blocks out. I **think** that will work. Now I just need a helper... Quote Link to comment
skunk Posted June 5, 2010 Report Share Posted June 5, 2010 make a stand for it out of the two bits that are already there, which'll facilitate you moving it in future sounds like best idea Quote Link to comment
datsunrides Posted June 5, 2010 Report Share Posted June 5, 2010 You could look into renting a couple house or toe jacks. They have the capacity and are designed for a similar type of lifting. There is also a type of lever called a (no kidding) johnson bar that may work, but would need to be used in stages, not all at once. HTH. Mark Quote Link to comment
datsunwizard Posted June 5, 2010 Report Share Posted June 5, 2010 Since have 3 mills in the work shop, I can give you some input. First off you will need lots of blocking( 3/4" plywood) and a long bar and a helper. You need two get rid of that tubing first. Metal to metal contact is not good, if the mill starts to slide on that tubing you will not be able to stop it. Get some new wood blocking under the four corners of the mill, by prying up on the front of the mill, inserting the new blocking . Now do the rear side like the front. Next remove the exsiting tubing and your old blocking. To get the mill on the ground, pry the mill up, then remove one block on the front side (both corners), then do the rear side. Keep repeating the proceedure untill its on the ground. Please be very carefull, take your time, be safe. You need to be respectful of that 2000lbs. If it starts to get away from you, let it go. It might damage the mill, but you can live another day to play with Datsuns. If you need any other help with the mill, in care or operation, just ask. Quote Link to comment
izzo Posted June 5, 2010 Report Share Posted June 5, 2010 a one ton car jack man, do one corner or one side at a time. Tie the top to the wall beam or something to keep it from tipping to far over. done deal. Quote Link to comment
thisismatt Posted June 5, 2010 Report Share Posted June 5, 2010 Engine hoist isn't really a safe option I don't think. The mill weighs just at 2000 pounds. I hauled it home in my 620 KC. I removed the head and made two trips. I have a 2 ton chain hoist that I used to put the head back on the column. I don't have a good way to lift it now that it's in place. I'm thinking of using a prybar (long piece of 1.5" square tubing) to lift one side and knock the blocks out. I **think** that will work. Now I just need a helper... So what's wrong with a 2 ton hoist? Quote Link to comment
datzenmike Posted June 5, 2010 Report Share Posted June 5, 2010 Looks tall enough to tip to the side and lift the other enough to slip the wood out, set down and tip the other way for the other side. Use a floor jack and a length of wood to push up under the table to lift. Quote Link to comment
slodat Posted June 5, 2010 Author Report Share Posted June 5, 2010 I used the pry bar method mentioned by datsunwizrd. Thank you all for your help!! It is on the ground and about to be powered up!! Quote Link to comment
78kingcab Posted June 6, 2010 Report Share Posted June 6, 2010 nice score slo,, i might just have a lil basic spacer job for ya ...ill let ya know.... :cool: Quote Link to comment
datsunwizard Posted June 6, 2010 Report Share Posted June 6, 2010 I am glad it worked for you. Get some way lube and start making chips. Have fun with your new toy! Quote Link to comment
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.