Justin Berni Posted August 12, 2014 Report Share Posted August 12, 2014 So I picked up a new 720 today, drive it home fine, no problems. But later in the day I was going somewhere and ran out of gas, managed to get to a gas station and fueled up, but ever since then it won't stay running unless I'm on the gas, and if I turn the idle screw up it helps a little, but than I'm idling way to high! Do you guys think it's just that I got some shit sucked up into the carb running so low on gas? Any suggestions? 1 Quote Link to comment
that-son Posted August 12, 2014 Report Share Posted August 12, 2014 most likely you "got some shit sucked up" and it's clogged your line, carb, pump or filter. got a repair manual yet? congrats on the new purchase and hope you figure it out. 1 Quote Link to comment
Justin Berni Posted August 12, 2014 Author Report Share Posted August 12, 2014 Yeah I have a manual for it. I'm gonna replace the filter in the morning and see if that helps, I just hope I don't have a clogged jet or something. 1 Quote Link to comment
bananahamuck Posted August 12, 2014 Report Share Posted August 12, 2014 I am not familiar with 86 technology but, does your carb have the two drain plugs on the underside of float bowl ? Sometimes you can pull one out at a time and drain some of the crap out ( water and such) then fill bowl up with gas and water separator (Heat type stuff) and pull them again. Never do it hot 1 Quote Link to comment
Justin Berni Posted August 12, 2014 Author Report Share Posted August 12, 2014 I'm not sure, I'll have to check. I'm a little scared to mess with the carb too much, cuz I've never really tore one apart. I think I'm gonna goto pick n pull and play with one there before I do anything to mine, I'd rather fuck up and learn on a junk yard part. Thanks for the advice tho, I'll look in to that in the morning! 1 Quote Link to comment
bananahamuck Posted August 12, 2014 Report Share Posted August 12, 2014 Oh yeah,, it isn't really taking the carb apart, it is just taking drain plugs out. I can totally relate to where your coming from I would definitely think long and hard before taking a Hitachi apart for sure. They are a nightmare inside. But your truck might be to new to even have the drain plugs. 2 Quote Link to comment
Justin Berni Posted August 12, 2014 Author Report Share Posted August 12, 2014 Oh yeah,, it isn't really taking the carb apart, it is just taking drain plugs out. I can totally relate to where your coming from I would definitely think long and hard before taking a Hitachi apart for sure. They are a nightmare inside. But your truck might be to new to even have the drain plugs. I'll look into that in the morning forsure. If it's not a clogged filter or carb, anyone else know what might cause my truck to die when I'm not giving it gas? The idle isnt very steady. 1 Quote Link to comment
wayno Posted August 12, 2014 Report Share Posted August 12, 2014 It was ran out of fuel, my guess is that it picked something up from the bottom of the tank, but it seems like if it did that it would not run at all, and it also would seem to me that the filter would have stopped anything from even making it to the idle jet/jets. I personally don't know anything about them ECU carbs on them trucks, nor do I know much about the electric fuel pumps on them trucks. I have a question, you said it ran out of fuel, but somehow you got it to the fuel station, how did you manage getting it there without fuel? 1 Quote Link to comment
Justin Berni Posted August 12, 2014 Author Report Share Posted August 12, 2014 Ran out once, but it started after, then when I got down the street to the gas station it died again, I didn't try starting it again tho, I just pushed it to a pump than put some gas in. The gauge was on E, but maybe I actually never even ran out, hmmm 1 Quote Link to comment
Justin Berni Posted August 12, 2014 Author Report Share Posted August 12, 2014 Pulled the air cleaner off to look inside, and it looks like the fuel isn't spraying like it's supposed to, I think something is clogged in the carb 1 Quote Link to comment
banzai510(hainz) Posted August 12, 2014 Report Share Posted August 12, 2014 Typical datsun owner runs on empty I bet the dirt suck into the idle jet. many people inccrease the idle speed screw to compensate but really your running off the main fuel jet. clean the idle jet which you should also have a 12vcolt wire going to(anti desieling selinoid) cleaan this then you can readjust back to stock settings. also replace the fuel filter and then maybe cut it open to give a reading how dirty your tank is. 2 Quote Link to comment
Justin Berni Posted August 12, 2014 Author Report Share Posted August 12, 2014 It diesels pretty bad when I shut it off, if that tells you anything. How should I clean it? 1 Quote Link to comment
banzai510(hainz) Posted August 12, 2014 Report Share Posted August 12, 2014 I dont know stock napz carbs. but where the 12volt wire that goes to it youll unplugg it and unscrew the selenoid and assume there will be a iddle jet and or holder. then blow it out till you csan see thru the jet. Be honest Ill steer you to datzenmike for more info. he has photos of the carbs but on weber DGV AVs there is a brass screw looking cap ,unscrew and the idle jet is in that and youll blow it out. Quote Link to comment
Justin Berni Posted August 12, 2014 Author Report Share Posted August 12, 2014 This is the anti diesel one solenoid, correct? I don't know much about real carburetors, all I know is small engine carbs haha 1 Quote Link to comment
Nissan_Boy85 Posted August 13, 2014 Report Share Posted August 13, 2014 Solve the problem and get a weber. But seriously, check the float level and maybe do the drain thing. Or maybe someone knows the "cover the intake with a rag so it sucks the bowl dry and pulls any crap out" trick? Roadkill (episode 3) is edumacational. 2 Quote Link to comment
Justin Berni Posted August 13, 2014 Author Report Share Posted August 13, 2014 Solve the problem and get a weber. But seriously, check the float level and maybe do the drain thing. Or maybe someone knows the "cover the intake with a rag so it sucks the bowl dry and pulls any crap out" trick? Roadkill (episode 3) is edumacational. Once I sell my wheels I'm getting a weber. And roadkill is a dope show, besides that they call their Z "Rotsun", can't stand that.. I'll have to go back and watch that episode again, I dont remember it, thanks! 1 Quote Link to comment
Nissan_Boy85 Posted August 13, 2014 Report Share Posted August 13, 2014 Not positive on the number, but its the cheap truck challenge episode. 2 Quote Link to comment
Justin Berni Posted August 13, 2014 Author Report Share Posted August 13, 2014 Not positive on the number, but its the cheap truck challenge episode. You were right, episode 3, watching it now. I'm gonna try that little trick in the morning. 1 Quote Link to comment
Justin Berni Posted August 13, 2014 Author Report Share Posted August 13, 2014 Played with the carb a little, hopped in to go around the block real quick and see if it was any better, at first it wouldn't go into gear, once I got it in gear I went around the block, I come back to find that I left a trail of tranny fluid. The tranny drain plug was loose as hell, I could spin it with my finger. So I tightened it up and left the truck parked until tomorrow so I can put fluid in.. 1 Quote Link to comment
datzenmike Posted August 13, 2014 Report Share Posted August 13, 2014 To you it's a new truck and not to be trusted!!!!!! You can't just jump in a drive around you have no idea how well the other owner looked after it. What if it seizes up because it's out of oil??? Check ALL fluids, engine oil, transmission, differential... preferably replace them all with fresh and a new oil filter. Check the belts and all heater and rad hoses. There is a small fuel filter on the bottom of the electric fuel pump. The dieseling, or run on is caused by you having the idle speed turned up. It's no longer on the idle circuit and the idle cut solenoid will have no effect. Turn ignition on and off while listening near the back of the carb. You should hear a light clicking if it's connected electrically. If no clicking find out why. To clear the idle circuit, unscrew and remove the idle cut solenoid being careful there is a spring and plintle that can fall out. Count the turns and remove the idle mixture screw, again there is a spring that is easily lost. If you have compressed air blow it into the idle mixture screw hole and the idle cut hole. Wear goggles. If you don't have air get a can of carb cleaner, the kind with a red straw like the WD-40 cans and spray liberally into both holes to clear them. This should get your idle back. Turn idle down as low as it will go. Turn idle mixture in and out to find the smoothest fast idle. Turn idle speed down and repeat the in and out adjustment settling for a point about half way between where idle is strongest. Turn idle speed down and repeat until you cannot improve the idle quality and the idle is around 750-800. Be sure to check the timing (3-5 degrees BTDC) and if adjusted re-check the mixture and idle speed again. 2 Quote Link to comment
Justin Berni Posted August 13, 2014 Author Report Share Posted August 13, 2014 To you it's a new truck and not to be trusted!!!!!! You can't just jump in a drive around you have no idea how well the other owner looked after it. What if it seizes up because it's out of oil??? Check ALL fluids, engine oil, transmission, differential... preferably replace them all with fresh and a new oil filter. Check the belts and all heater and rad hoses. There is a small fuel filter on the bottom of the electric fuel pump. The dieseling, or run on is caused by you having the idle speed turned up. It's no longer on the idle circuit and the idle cut solenoid will have no effect. Turn ignition on and off while listening near the back of the carb. You should hear a light clicking if it's connected electrically. If no clicking find out why. To clear the idle circuit, unscrew and remove the idle cut solenoid being careful there is a spring and plintle that can fall out. Count the turns and remove the idle mixture screw, again there is a spring that is easily lost. If you have compressed air blow it into the idle mixture screw hole and the idle cut hole. Wear goggles. If you don't have air get a can of carb cleaner, the kind with a red straw like the WD-40 cans and spray liberally into both holes to clear them. This should get your idle back. Turn idle down as low as it will go. Turn idle mixture in and out to find the smoothest fast idle. Turn idle speed down and repeat the in and out adjustment settling for a point about half way between where idle is strongest. Turn idle speed down and repeat until you cannot improve the idle quality and the idle is around 750-800. Be sure to check the timing (3-5 degrees BTDC) and if adjusted re-check the mixture and idle speed again. I realize now I should have done this, all I checked was engine oil, and coolent.. Since I already know what's up with the transmission fluid I guess I still need to check diff. fluid. And I'll play with the carb more tomorrow. What fluid do I need for tranny? Also, getting idle correct is tough because it's very unsteady, so it'll sound like it's where it should be, than drops for a minute, and dies Quote Link to comment
datzenmike Posted August 13, 2014 Report Share Posted August 13, 2014 Sounds like you have an automatic so make sure it's Dexron ATF. Clean the carb as per instructions and it should idle better. Then you can set the mixture properly. Quote Link to comment
Justin Berni Posted August 13, 2014 Author Report Share Posted August 13, 2014 Sounds like you have an automatic so make sure it's Dexron ATF. Clean the carb as per instructions and it should idle better. Then you can set the mixture properly. It's a 5 speed. Quote Link to comment
84720FourWheel Posted August 13, 2014 Report Share Posted August 13, 2014 API GL4 yellow metal safe. It HAS to be yellow metal safe or it will eat up the syncros. Royal purple makes some compatible stuff. very spendy though. 1 Quote Link to comment
arizonajones Posted August 18, 2014 Report Share Posted August 18, 2014 Sta-Lube at Napa. I went all over town looking for GL4 and Napa was the only place I found it. I even had a few sales people tell me it didn't matter - but they were wrong. Quote Link to comment
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.