tycot1 Posted April 14, 2011 Report Share Posted April 14, 2011 my tail lights are quite dim on my 510 so i am thinking about ordering some led bulbs. i guess because the 510s are so low compared to todays vehicles and the coupe lights have the horizontal bars shadowing the lenses they almost look like they are not even on. they are not on in the pic though.they are about $20 each x 6 bulbs so i am wondering if they will actually be worth spending the $. they draw less power right? has anyone done this bulb install and were you happy with the results? Quote Link to comment
Logical1 Posted April 14, 2011 Report Share Posted April 14, 2011 Not sure about where your ordering from but it makes huge difference! I have used the replacement LED Lamps from here: 12v LED's and have had amazing success. I would caution you on ordering any LED lamps that look like the old school 'star trek' leds for replacement, those are the cheaper rip-off style that are very dim still. most modern bright LEDs are flat and squarish looking. Examples: Crappy and cheap: Nice and Bright: It may cost a bit more in the short term but they save your plastic lenses (no heat) are much brighter and last FOREVER! Quote Link to comment
MicroMachinery Posted April 14, 2011 Report Share Posted April 14, 2011 Sorry, I don't have much input for the question at hand, but I just wanted to say that's a sweet looking 510. Have any more shots? Quote Link to comment
Radim Posted April 14, 2011 Report Share Posted April 14, 2011 You might need a new one of them turn signal relay control thing-a-majigers. LEDs sometimes cause the turn signals to flash faster than usual.... local Auto parts store should have an Electronic controller that works with them. Quote Link to comment
tycot1 Posted April 18, 2011 Author Report Share Posted April 18, 2011 so here is the only bulb my local supplier had. junk? you tell me. Quote Link to comment
tycot1 Posted April 18, 2011 Author Report Share Posted April 18, 2011 which side has the new bulbs? which side has the old tarnished bulbs with the corroded up bulb holders? Quote Link to comment
tycot1 Posted April 18, 2011 Author Report Share Posted April 18, 2011 the right side has the old bulbs and the left has the new. look at the glow from the inside with the old bulbs and look at the concentrated glow of the new bulbs in the next pic. i quite obviously have the junk leds. with the leds plugged i have no brake or signal lights on the same side, the side with the old bulbs will flash though. as soon as i put the old 1157 back in the flashers and brake lights work. JUNK. in checked out the site provided and im not sure which style would be the best one to get. the same one posted in the pic? Quote Link to comment
tycot1 Posted April 18, 2011 Author Report Share Posted April 18, 2011 these are the leds. Quote Link to comment
Z-train Posted April 18, 2011 Report Share Posted April 18, 2011 http://www.superbrightleds.com/cgi-bin/store/index.cgi?action=DispPage&Page2Disp=%2F1157.htm I changed the intrument bulbs in my 620 to LEDs from this place.THe original bulbs drew 3.4 watts.The LED replacements drew .27 watts. Quote Link to comment
thisismatt Posted April 18, 2011 Report Share Posted April 18, 2011 Your flashers won't work with LEDs because the flasher relies on the current draw of the incandescent bulbs in order to operate (LEDs don't draw enough current). You'll need to use a solid state, non-load based flasher if you use LEDs Quote Link to comment
tycot1 Posted April 18, 2011 Author Report Share Posted April 18, 2011 so i will need to change the signals in the front to led too i guess right, or would the new flasher unit work with the old bulbs. any ideas on which exact bulbs are the best? Quote Link to comment
tycot1 Posted April 18, 2011 Author Report Share Posted April 18, 2011 here is a token pic. i started my wet sand today and will be polishing by mid week after hours at my shop. i have all of my business decals finished that will go on the number plates and i wanted to polish before applying them. Quote Link to comment
thisismatt Posted April 18, 2011 Report Share Posted April 18, 2011 I guess it would depend on the flasher unit as for how it would react with a combination of LED and incandescent bulbs. As long as it's not relying on the current draw, but can handle the current of the incandescents, then it should be fine. Perhaps the best thing to do would be to get a solid state flasher and run it to a relay that could handle the incandescent current load. Quote Link to comment
Logical1 Posted April 18, 2011 Report Share Posted April 18, 2011 If you don't want to change out your flasher, you can add a dummy load lamp or resister that simulates the current draw. Quote Link to comment
izzo Posted April 18, 2011 Report Share Posted April 18, 2011 one of these would do if you can find one that fits http://www.superbrightleds.com/cgi-bin/store/index.cgi?action=DispPage&Page2Disp=/flashers.htm Quote Link to comment
MicroMachinery Posted April 18, 2011 Report Share Posted April 18, 2011 here is a token pic. Quote Link to comment
Shagy Posted April 18, 2011 Report Share Posted April 18, 2011 I'm interested to see a parking vs brake light comp photo. The difference is usually not big enough for me. I've been selling LED's for 8 years now and I have still not seen a bulb that I've liked for brake/run/turn signal applications. Parking/corner lamps ones work fine. I've seen some people take the DOT approved ones and make them fit in their housings. They are bright. The last conversion I saw used a 4" round from a semi trailor. There is a big difference from running brightness to stop brightness. The flasher does not care what type of bulb type your using. you can use the OEM stuff up front and LED in the back, but you WILL still get a tweaker blinker. Look for an electronic flasher unit. I think they are $25 and they work very well. Quote Link to comment
HRH Posted April 19, 2011 Report Share Posted April 19, 2011 You can get LED flasher units at NAPA and probably other places. We sell them for big trucks, as many of those run LED running lights, etc. nowadays. With LEDs and a regular flasher, the lights won't flash because there's not enough resistance to cycle the flasher unit. Quote Link to comment
ajen68510 Posted June 5, 2011 Report Share Posted June 5, 2011 so here is the only bulb my local supplier had. junk? you tell me. hey Tyson, V-LEDS.com just across the border has a great choice in LED bulbs for all applications. Have done my Dime from front to back, including all dash lights. The turn signals require resisters 3OHM for 2 bulbs, 6OHm for 4 bulbs. Or just change to a new electronic flasher it does not care about resistance. I tried the bulbs u have in the package, they were not very bright. Changed to the V-LEDs . Quote Link to comment
Javin Posted June 5, 2011 Report Share Posted June 5, 2011 I'm interested to see a parking vs brake light comp photo. The difference is usually not big enough for me. I've been selling LED's for 8 years now and I have still not seen a bulb that I've liked for brake/run/turn signal applications. Parking/corner lamps ones work fine. I've seen some people take the DOT approved ones and make them fit in their housings. They are bright. The last conversion I saw used a 4" round from a semi trailor. There is a big difference from running brightness to stop brightness. The flasher does not care what type of bulb type your using. you can use the OEM stuff up front and LED in the back, but you WILL still get a tweaker blinker. Look for an electronic flasher unit. I think they are $25 and they work very well. I think I got my Electronic flasher for ~$8 at auto zone. EDIT: Looks to be $7 online. I THINK this is the one I snagged for turn signals. Then got one with a higher max for the emergency flashers from NAPA. Quote Link to comment
Spades Posted June 5, 2011 Report Share Posted June 5, 2011 LED's often offer much more lumens and lifespan than their incandescent counterparts, but it is at a cost. Most cheaper LED's have a spotlight effect, a benefit for most applications, but not usually for car applications. I have seen some good LED bulbs, but they are often expensive, so I have never bothered with them yet. I prefer a high quality incandescent that offers a bright white white light that uses the same amperage and voltage as the stock bulb so that I don't have to change flashers or worry about if I am buying one of the "good" LED bulbs. With that said, LED's are getting cheaper and better every day, if you find a good set up bulbs(for the right price), I would say it is worth the expenditure. Quote Link to comment
ajen68510 Posted June 5, 2011 Report Share Posted June 5, 2011 LED's often offer much more lumens and lifespan than their incandescent counterparts, but it is at a cost. Most cheaper LED's have a spotlight effect, a benefit for most applications, but not usually for car applications. I have seen some good LED bulbs, but they are often expensive, so I have never bothered with them yet. I prefer a high quality incandescent that offers a bright white white light that uses the same amperage and voltage as the stock bulb so that I don't have to change flashers or worry about if I am buying one of the "good" LED bulbs. With that said, LED's are getting cheaper and better every day, if you find a good set up bulbs(for the right price), I would say it is worth the expenditure. Yes, your right about the expense. I think i paid in range of $40.00 bulb from V-LEDS. but i have 72 hi intensity Leds per bulb, low amps, and twice the brightness. Not sure how long they will last. (Manufacture claims 20 times the life span) Avantage is very little load on our old wiring, and able to be seen in daylight. Quote Link to comment
oldschool90 Posted June 6, 2011 Report Share Posted June 6, 2011 I've seen some people take the DOT approved ones and make them fit in their housings. Thats what I did. The only thing though is that I had to cut up my tail light buckets to fit them. I'm interested to see a parking vs brake light comp photo. Well since you asked........ Quote Link to comment
ajen68510 Posted June 6, 2011 Report Share Posted June 6, 2011 Thats what I did. The only thing though is that I had to cut up my tail light buckets to fit them. Well since you asked........ Niiiiice ! Quote Link to comment
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.