Zeusimo

Dibs

Well Anyone From Modesto Area I've Got A Few Ppl To Meetup At Modesto Innout At 9AM We Will Leave At 9:15 :)

Remove The Panels From The Inside So You Can Get A Better View I THINK They Have Some Kind Of Washer That Holds The Tabs In Place

Are You Leaving From Modesto? Also Trying To Gather A Few Datnuts Together

CA18DET Thread On This Soon

So Can You Remove The Tach? Or Would You Have To Get A Whole New Cluster??? That Dash Came Out Nice :)

I Haven't Been On My Computer For A While... Been Using My iPhone Ever Since I Got It Decided To Keep Annoying Everyone :D

My Truck Has Grooves Alone The Bottom Of The Intake Too But Only Goes On Cyl 1 And 4

I Had To Cut The Center + Piece With A Cut Off Wheel Then Hammered The Bearings Out With Lots Of WD40 Only Did This On 1.. The Other Two Came Out Just With A Hammer

Did You Grease The Bearing? Noise Should Go Away After Every Ball In The Bearing Gets Grease When I Changed The Clutch In My Truck It Did That Drove If For An Hour And Went Away For The Grinding You Might Have Not Aligned The Clutch Right.. But I Don't Think So

Meee!

How Much Do Tou Want For That Tach And Smiley Bumpers? Also Show Us What You Do For The Front Suspension :)

Yeah!! Got It Going :D Needs Abit Of Fine Tuning And Done I Guess It Was So Dirty I Had To Use 3 Cans Of Carb Cleaner http://www.youtube.com/watch?v=odp5AYRhBQU

So Ur Leaving From Riften? How Do You Get Out Of Skyrim??

So I Retorqued Intake/Exhaust Checked For Leaks W/ Starting Fluid Squirted A Ton Of Carb Cleaner In The Carb When Runing Now Idles Reved A Few Times Idled And Died After A Min Cuz I Ran Out Of Gas Gonna Go Get Some More Gas But I THINK Everything Is Ok

How Much For Ashtray Light Steering Wheel Stock Temp Gauge Shipped To 95357? Also Do The Seat Belts Hang From The Roof? Or Just The Floor

@Bonvo Same Thing With That Screw, Didn't Even Idle Before I Had To Cut It Down Almost Three Threads To Get It To Tighten Also Used Two Gaskets, One Before And After The 1/16" Spacer Plugged The Vaccum Lines With Tighter Hoses And It Helped Alittle Bit But Tommoz I Will Try To Get A Torque Wrench And Retorque Intake/Exhaust Yeah... BTW What Is Intake/Exhaust Torque Spec?

Yeah I Removed The Choke And Pin From Valve If I Hook Them Up It Will Just Die

So I Installed A Rebuilt 75 710 L20b Carb, Plugged The Holes, Removed Idle Cam, Choke, And Anti-Diesel Valve. Set Timing To 12BTDC, Adjusted Valves, New Kyosan Fuel Pump, New Gapped Plugs 0.030, And Points 0.020, Dwell No Clue... Bled Air Out Of Cooling System, Removed Secondary Points, Rebuilt Top-End U67 Peanut U20 Cam Everything On Motor Lines Upto TDC 11:28, Cam/V-Notch, 2 On Sprocket, New Beck/Arnley Chain So Car Starts Up Fine And Doesn't Missfire Carb Squirts Strong Gas When Off For Only 2-3 Pumps When Off It Is Very Responsive When Giving It Gas But It Doesn't Idle Right Even When Hot Goes From 800-1200 Up And Down Every 5 Secs? Not Sure If This Is Right I Did Have A Holley On It Before.. And It Ran GOOD But It Seems Too Much For Even A V8? I Much Rather Have A Hitachi/Weber I Still Need To Find/Install PCV Hose To Intake Will L20b Carb Not Work With L18? Video: http://www.youtube.com/watch?v=UMANgiC1CeQ

It's Not A 73 610 Or A Datsun It's A POS Ford There I'm Happy