Crashtd420 Posted October 31, 2017 Report Share Posted October 31, 2017 Hell I never had a dizzy or carb till I got my datsun .... Quote Link to comment
datsunfreak Posted November 1, 2017 Report Share Posted November 1, 2017 Was thinking of just putting the quad carbs on and not messing with the stock setup. What do you guys think? Get a 1200 carb, swap your jets and throttle cable wheel into it, enjoy. 1 Quote Link to comment
head trauma johnny Posted November 1, 2017 Author Report Share Posted November 1, 2017 Just order a intake/exhaust manifold gasket and a valve cover gasket. Once they get in in swapping in the new setup. Looked at it and it has a vacuum port so should be quick and easy. Just have to figure out what air filter set up I'm going with. Quote Link to comment
head trauma johnny Posted November 2, 2017 Author Report Share Posted November 2, 2017 Think I'm going with these. https://m.ebay.com/itm/Set-of-2-Black-Foam-Pod-Filters-50mm-Honda-CB-CL350-360-450-CB500T-/182443509320?nav=SEARCH Quote Link to comment
head trauma johnny Posted November 9, 2017 Author Report Share Posted November 9, 2017 A14 no carb https://imgur.com/gallery/1jUHP Well it took me about 1 1/2 hours to pull the carb and manifolds off this morning. I went to see if the headers would fit and no luck. First the intake and exhaust ports are slightly smaller than the head and the the tubes are 2" too long and would hit the crossmember. If I shorten them to fit in between the motormount and cross member I would still need to angle the collector out to miss the trans. So now I don't know if I should do the mods to the headers or get a new carb (with electric choke) to replace the worn out stock one. Or option 3 which I was going to do down the road after I got the car sorted is to fab up a draw through turbo setup. Leaning towards modding the headers to fit since I have them and air pod filters on the way. What are your opinions? Quote Link to comment
Cosmonaut Posted November 12, 2017 Report Share Posted November 12, 2017 That's because they belong on a Datsun roadster 1600/2000 Quote Link to comment
head trauma johnny Posted November 18, 2017 Author Report Share Posted November 18, 2017 A14 exhaust manifold https://imgur.com/gallery/NGuQ0 I'm going to use the stock exhaust manifold and the quad carb intake. Do I need to make a special plate to bolt to the gasket in the picture or just bolt it down? Thanks in advance. Quote Link to comment
datsunfreak Posted November 19, 2017 Report Share Posted November 19, 2017 I'm going to use the stock exhaust manifold and the quad carb intake. Do I need to make a special plate to bolt to the gasket in the picture or just bolt it down? That doesn't really do anything but make the carb hot. You don't really need to do anything with it. Except throw it in the trash. ^_^ 2 Quote Link to comment
head trauma johnny Posted November 30, 2017 Author Report Share Posted November 30, 2017 https://i.imgur.com/pHYBtfC.jpg So everything is finally installed. Just when I started it fuel was pouring out the front of the carbs. Do I need a fuel pressure regulator? Or do I need to run its own return line instead of using stock setup(pictured). Or are the floats not working properly? Thanks. Quote Link to comment
Crashtd420 Posted November 30, 2017 Report Share Posted November 30, 2017 Was this a working setup? Do you know? First I don't think they need a return line.... when i was working with motorcycles I never saw a return line.... ( they may exist but I never saw them) 2nd what type of fuel pump... if a stock mechanical I would say no to the regulator but it may help. Do you know what your fuel pressure Is and what those carbs want? You could try gravity feeding the carbs.. if that works better then you have to much fuel pressure.. If it does the same thing I would say have a look at your float level and operation.. Quote Link to comment
head trauma johnny Posted December 1, 2017 Author Report Share Posted December 1, 2017 So the 2 that were leaking, I took them apart and cleaned them. I discovered that there was the wrong o-rings installed on the float needle housing and replaced them with better fitting and fuel rated ones. Re-installed the carbs and it ran good. Took it for my first test run. Now I need to start on the electrical issues. No turn signals,horn, heater lever won't budge. A lot more work ahead. Quote Link to comment
Crashtd420 Posted December 1, 2017 Report Share Posted December 1, 2017 Nice job fixing it.... always good when its something simple.... Quote Link to comment
sunny310 Posted December 23, 2017 Report Share Posted December 23, 2017 definitely following this...would u be able to make videos of it? Quote Link to comment
head trauma johnny Posted April 21, 2019 Author Report Share Posted April 21, 2019 So started working on the 210 again. I ditched the motorcycle carbs and replaced them with a Weber 32/36 I stole off my wifes VW bug project. It's running to rich so I ordered some smaller jets. I also picked up some 2000 Sentra seats and seat belts from the junk yard. The stock ones are crumbling to pieces. I fabricated the driverside bracket this morning to utilize the factory mounting holes. Got it installed along with the Sentra seat belt. it surprisingly fit with a little bit of trimming. Very pleased with the out come. Now time for the passenger side. Hope to have this finally on the road soon. Will update with any other progess. 2 Quote Link to comment
head trauma johnny Posted April 21, 2019 Author Report Share Posted April 21, 2019 1 Quote Link to comment
head trauma johnny Posted May 2, 2019 Author Report Share Posted May 2, 2019 Going to be picking up some 280zx strut/brake assemblies today. I was wondering what rear spring and shock combo everyone was running? Was thinking of going with 150# springs in the front since it's going to be my daily. Also what are your thoughts on the stop tech brakes? They are about double the price of other brands. Thanks. Quote Link to comment
datsunwhacko520 Posted May 2, 2019 Report Share Posted May 2, 2019 I drove a brown clone of your car in high school. Actually my first experience with a datsun. I didn't appreciate it way back when. Was a total slug with that automatic....had to keep pedal on floor to keep hamster wheel spinning. Sold car and buyer drove it to Mexico and then back to Oregon. Great seeing another $300 datsun evading the scrappers without scruples😀.they get crushed EVERY day.😣😢 1 Quote Link to comment
head trauma johnny Posted May 2, 2019 Author Report Share Posted May 2, 2019 Well got the 280zx set up. Started the interior color change and dash pad restoration. Unfortunately when I was taking out plastic bits from the interior, the A-pillar covers shattered to pieces. So I'll be on the lookout for those. Quote Link to comment
gdat210 Posted November 7, 2019 Report Share Posted November 7, 2019 do you still have the motorcycle carb setup? Quote Link to comment
pdp8 Posted November 19, 2019 Report Share Posted November 19, 2019 (edited) On 10/31/2017 at 8:42 AM, Crashtd420 said: Hell I never had a dizzy or carb till I got my datsun .... These little cars don't have room for long words, hence the abbreviations. 🙂 When I put the Webber on I found I was way rich, not really from jetting but because it was too much carb for the manifold vacuum and I was on the power valve all the time. Modification of the power valve solved the problem. I still don't get the 39MPG I got with the Hitachi but it's about 35. Edited November 19, 2019 by pdp8 Quote Link to comment
head trauma johnny Posted December 21, 2019 Author Report Share Posted December 21, 2019 So finally getting some Time to work on the Datsun again. Since the last time I posted, I've picked up a 4 speed,clutch pedal setup, ordered a lightweight flywheel from Japan. I'm also about to order the exedy clutch kit, master cylinder,and slave. I re-jetted the Weber. Car runs good enough for now until the swap is done. Then I'm going to focus on engine and supension. Was looking for pistons but could only find high compression 79mm pistons for an A15. Can you bore the a14 cylinders 3mms? Do the a14 and a15 use the same block and connecting rods. hope to have another update with pics soon with the new trans in. Quote Link to comment
az_rat210 Posted December 29, 2019 Report Share Posted December 29, 2019 Try this page for boring over http://datsun1200.com/modules/mediawiki/index.php?title=Justy_Piston_Swap Mike bored out an A14 to 1600cc for his Ice Racer and used Justy Pistons. I will see if I can find more info on this from the Yahoo Forum. 1 Quote Link to comment
az_rat210 Posted December 29, 2019 Report Share Posted December 29, 2019 Ok, here is blownb310's car domain link. Hope this helps you out. http://www.cardomain.com/ride/2447688/1977-datsun-b210/ 1 Quote Link to comment
head trauma johnny Posted December 29, 2019 Author Report Share Posted December 29, 2019 Good information, thanks. Quote Link to comment
head trauma johnny Posted January 11, 2020 Author Report Share Posted January 11, 2020 Just received my lightweight flywheel from Japan today. Still waiting on a few more parts to start the manual swap. Quote Link to comment
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.