that one guy Posted September 29, 2012 Report Share Posted September 29, 2012 Ok, not studs, but bolts. Head bolts to be specific. I've gotten exactly 2 out, and the rest are stuck. And i mean stuck. I rounded off 3 allen wrenchs, and even snapped one in half. I need to get them out to remove the head, but only because I need the block in good condition, the head is toast. Any suggestions? Quote Link to comment
Dat Lurka Posted September 29, 2012 Report Share Posted September 29, 2012 They're not stuck. You're doing it wrong :poke: http://www.tooltopia.com/gearwrench-80660.aspx?utm_source=googlebase&utm_medium=cse&utm_term=KDT80660&utm_campaign=googlebase_18u&gclid=CPjylLqh2rICFQsGnQodMQIAnw Heck you can get one at Advance. Quote Link to comment
that one guy Posted September 29, 2012 Author Report Share Posted September 29, 2012 hmmmm......... and you're sure this'll work? Cause I used a regular allen wrench with a 4 foot breaker bar.... Quote Link to comment
Laecaon Posted September 29, 2012 Report Share Posted September 29, 2012 are the bolts rounded out? If not time to get a 10mm Allen socket, and not from harbor freight. Maybe put the two back in and run the motor til hot and then try to remove. I fear you are more likely to snap off the bolts in the block.worst comes to worse, you could grind the heads off the bolts take the head off and double vise grip the bolts and use lots of on blaster down the threads. Just some brainstorming... Quote Link to comment
Ranman72 Posted September 29, 2012 Report Share Posted September 29, 2012 are the bolts rounded out? If not time to get a 10mm Allen socket, and not from harbor freight. Maybe put the two back in and run the motor til hot and then try to remove. I fear you are more likely to snap off the bolts in the block.worst comes to worse, you could grind the heads off the bolts take the head off and double vise grip the bolts and use lots of on blaster down the threads. Just some brainstorming... I second the thought of cutting tops off if heads are toast and double vise grip you can also heat the block with a torch to expand just dont get stupid and turn it red hot Quote Link to comment
Dat Lurka Posted September 29, 2012 Report Share Posted September 29, 2012 hmmmm......... and you're sure this'll work? Cause I used a regular allen wrench with a 4 foot breaker bar.... Positive. You're cheapo allen wrenches gave out before you broke that 60lb bolt loose. 10mm hex head socket. Well positive enough. Quote Link to comment
that one guy Posted September 29, 2012 Author Report Share Posted September 29, 2012 Can't run the motor, sitting on a stand in need of a full tear down and rebuild, and yes the bolts are still good. Where do your propose I buy a 10mil socket at that won't snap and how do i get the snapped one out? Quote Link to comment
Dat Lurka Posted September 29, 2012 Report Share Posted September 29, 2012 Advance, Napa, Autozone, O'Reillys Whoever is convenient. ~10$ Snapped allen wrench? Reverse bit and/or backout bit set. these are all things you should have in a datto tool kit :poke: I've never removed and replaced stuff on a datsun without breaking something. Factory hardware is pretty weak. I'm really good at removing broken bolts now. I just did my head. They're in there real good at 60lbs. I actually broke a 3/8ths extension off in my 10mm hex socket :rofl: Quote Link to comment
Laecaon Posted September 29, 2012 Report Share Posted September 29, 2012 No to those places. Napa, sears maybe even lows for the kobalt line. Good tools don't break. I have yet to break one of my Allen keys and I have wailed on them. I use a napa hex socket for my head bolts. Cheap tools come back to bite you. Quote Link to comment
datzenmike Posted September 29, 2012 Report Share Posted September 29, 2012 Get a 1/2" socket with the Allen tip (10mm???) Oh and turn CCW. :lol: Quote Link to comment
Sealik Posted September 29, 2012 Report Share Posted September 29, 2012 Get a 1/2" socket with the Allen tip (10mm???) Oh and turn CCW. :lol: Correct.... you are also going to need it to torque the head bolts in place. Quote Link to comment
Ranman72 Posted September 29, 2012 Report Share Posted September 29, 2012 sears buy a craftsmen they are pretty good or if you can find one SK snap on mac something name brand Quote Link to comment
Draker Posted September 29, 2012 Report Share Posted September 29, 2012 I'll admit I have the harbor freight ones since I don't use them often. Never rounded or broke anything off. But if I already f'd up some stuff, I'd get some craftsman at least. Although, they are probably made from the same plant in china these days. Quote Link to comment
that one guy Posted September 29, 2012 Author Report Share Posted September 29, 2012 Thanks for all the advice guys!! Looks like I'm off to Lowes for some Kobalt goodness! Quote Link to comment
Dat Lurka Posted September 29, 2012 Report Share Posted September 29, 2012 Not sure what mine is but my Dad bought it in 75' and It still works great. Quote Link to comment
datzenmike Posted September 29, 2012 Report Share Posted September 29, 2012 That's back when a tool was naturally expected to last a lifetime. Everything is about cheaper cost and that can only mean cheaper materials and processes to do that. Today we've been trained to not expect things to last. Cell phones, cars, furniture, Quote Link to comment
Dat Lurka Posted September 29, 2012 Report Share Posted September 29, 2012 Hence most the things I own are twice as old as me. Those bolts are tough. I almost broke my grandfathers breaker bar :no: It stretched out a bit and one of the pins went flying across the shop. I never knew the man, his tools are all I have. Quote Link to comment
banzai510(hainz) Posted September 29, 2012 Report Share Posted September 29, 2012 Crafstman got soem nice 10mm hex heads Kobalt used to be USA now its Taiwan I believe. Craftsman is the most affordable at X mas time when I buy them up. Snap On Mac tools and some others are good but kill most ratsuners(kids w no money) Quote Link to comment
rayven14 Posted September 29, 2012 Report Share Posted September 29, 2012 Id try a snapon or something of equal quality and and impact wrench, I think its better than just brute force. Quote Link to comment
that one guy Posted September 29, 2012 Author Report Share Posted September 29, 2012 I bought a Kobalt bit, they only come in 3/8th's, and a 3/8th to 1/2 adapter and got all of them out but the one a snapped the previous allen wrench off in and one more that stripped out. Time to cut the heads off and vice grip dem bitches out o.O Quote Link to comment
Dat Lurka Posted September 29, 2012 Report Share Posted September 29, 2012 Good try! You got the tool now. Quote Link to comment
Laecaon Posted September 29, 2012 Report Share Posted September 29, 2012 It is my understanding that Kobalt is made by Snap-on. I am not saying that Kobalt and Snap-on are the same quality, just that its of decent quality. Husky is made by Stanley I do believe. Quote Link to comment
datzenmike Posted September 29, 2012 Report Share Posted September 29, 2012 I bought a Kobalt bit, they only come in 3/8th's, and a 3/8th to 1/2 adapter and got all of them out but the one a snapped the previous allen wrench off in and one more that stripped out. Time to cut the heads off and vice grip dem bitches out o.O Dream on. You just used cheap Allen wrenches. Vice grips are never going to work on a round bolt head. If you used a 4' bar how are vice grips going to improve on that? Get a good socket and the bolt will shear off before it will break. Snap them all off and slide the head up and off. Quote Link to comment
Dat Lurka Posted September 30, 2012 Report Share Posted September 30, 2012 He forgot the backout kit. Quote Link to comment
that one guy Posted September 30, 2012 Author Report Share Posted September 30, 2012 Dream on. You just used cheap Allen wrenches. Vice grips are never going to work on a round bolt head. If you used a 4' bar how are vice grips going to improve on that? Get a good socket and the bolt will shear off before it will break. Snap them all off and slide the head up and off. I don't want the head, the block is more important. Plus, once I cut the heads off the bolts and slide the head off, I can put some liquid wrench on em. And if that fails to work, I have a bunch of scrap metal tubing that I can weld onto the stud and get it out that way. The problem i was running into before buying the new bit was rounding out the allen wrench. No idea what brand or anythign, just found it laying around and it was the right size... Quote Link to comment
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.