OpelWagenGT Posted February 9, 2010 Report Share Posted February 9, 2010 So I'm finally getting ready to buy lowering blocks for the rear of my 1200 and I'm having some shopping issues. Most of the sets that I have found are for 3" axle tubes. When I measured my car it seems that they are 2" or even 2 1/8". Where would I get the correct lowering blocks, I am going for 3 or 4 inches of lowering. Quote Link to comment
OpelWagenGT Posted February 10, 2010 Author Report Share Posted February 10, 2010 26 views, no replies, I suppose I'm on my own then. :blink: Quote Link to comment
denveratsun Posted February 10, 2010 Report Share Posted February 10, 2010 No...not on your own...just that everyone is trying to find you some! I know that it's not uncommon to use the blocks from the kit with different Ubolts that fit the axle better. Those should be available from a number of sources online. Lookin forward to seeing it lowered! Quote Link to comment
Pumpkn210 Posted February 10, 2010 Report Share Posted February 10, 2010 In my locallity (Pierce County) there are several shops that specialize in springs and such, mostly indistrial applications that will make you springs or custom bend you some U bolts for cheep. The one in tacoma that I use for this type of thing is called Right Way Springs! Look around locally and Im sure you can find a spring shop that has the equipment in house! Quote Link to comment
OpelWagenGT Posted February 10, 2010 Author Report Share Posted February 10, 2010 Nice it's good to hear that I have help, I figured just making sure. :rolleyes: I just ordered the collars to lower the front and after taking a look at it I found that for the height I want I will also have to cut the springs or putt coil over sleeves on the collar. I might have to do something like this Quote Link to comment
Pumpkn210 Posted February 10, 2010 Report Share Posted February 10, 2010 How far down with the front are you goin? Quote Link to comment
OpelWagenGT Posted February 11, 2010 Author Report Share Posted February 11, 2010 as far as I can :P slam or go home! Quote Link to comment
bonvo Posted February 11, 2010 Report Share Posted February 11, 2010 dont use those clamps!!! one good hard knock and they will slide i would use them the way wagdatto sugested find where you want it to be with the clamps then weld a bead right below the clamp so it cant slide past that pointthat way its still "adjustable" but it wont go past the point of no return so to speak Quote Link to comment
OpelWagenGT Posted February 11, 2010 Author Report Share Posted February 11, 2010 dont use those clamps!!! one good hard knock and they will slide i would use them the way wagdatto sugested find where you want it to be with the clamps then weld a bead right below the clamp so it cant slide past that pointthat way its still "adjustable" but it wont go past the point of no return so to speak Have you had this happpen to you personally or someone you know? The clamps are supposed to be torqued to a certain amount. I understand that it would seem likley for this to happen but many many people have done it this way. Quote Link to comment
Guest kamakazi620 Posted February 11, 2010 Report Share Posted February 11, 2010 Have you had this happpen to you personally or someone you know? The clamps are supposed to be torqued to a certain amount. I understand that it would seem likley for this to happen but many many people have done it this way. just think about it 1800-2000 pound car being supported bya clamp??? Bonvo knows his shit listen to him!!! Quote Link to comment
datzenmike Posted February 12, 2010 Report Share Posted February 12, 2010 I know they work, but common sense says they 'could' slip, so bonvo is only right in saying so. I plan to run something like this and now will put a very small bead of weld below the clamp when in it's final position. Makes sense and can be ground down to change it. OpelWagenGT I tried machine shops, plumbing outlet and auto parts and could not fine these type of tube clamp. These are exactly what I want. Where did you find them??? Quote Link to comment
turbojunker Posted February 12, 2010 Report Share Posted February 12, 2010 just think about it 1800-2000 pound car being supported bya clamp??? Bonvo knows his shit listen to him!!! The whole 2000 lb isn't on one corner of the car. Quote Link to comment
WagDatto Posted February 12, 2010 Report Share Posted February 12, 2010 I have 300# springs, which is considered harsh... With a KA, which is fairly heavy. My collars havent slipped ONCE on my old powdercoated struts, and haven't slipped ONCE on my spray painted struts. No movement, and the car is daily driven... hard. Potholes included. If you're feeling sketchy about it, just toss some welds right below the clamp and done deal. Quote Link to comment
ariascarlos1990 Posted February 12, 2010 Report Share Posted February 12, 2010 skib has these on his goon. im thinkin about getting a set. Quote Link to comment
Skib Posted February 12, 2010 Report Share Posted February 12, 2010 skib has these on his goon. im thinkin about getting a set. yup, hit up Eric (datto510) hes the one that stuck em on there, he can tell you where he found em lol Iv hit bumps hard enough to knock my throttle linkage apart and Iv never had them slip Quote Link to comment
bonvo Posted February 12, 2010 Report Share Posted February 12, 2010 The whole 2000 lb isn't on one corner of the car. split that up thats 500lbs on that corner i know i wouldnt want 500lbs held up by a clamp im not saying they dont work m just saying a welded bead along the bottom would be cheap insurance as for having it happen to me no btu it has happened to other members of this forum Quote Link to comment
HRH Posted February 12, 2010 Report Share Posted February 12, 2010 I vote weld a bit on the bottom, for obvious reasons. What if you decide to take that quick left hander and find a bridge to jump? :D Quote Link to comment
OpelWagenGT Posted February 12, 2010 Author Report Share Posted February 12, 2010 I know they work, but common sense says they 'could' slip, so bonvo is only right in saying so. I plan to run something like this and now will put a very small bead of weld below the clamp when in it's final position. Makes sense and can be ground down to change it. OpelWagenGT I tried machine shops, plumbing outlet and auto parts and could not fine these type of tube clamp. These are exactly what I want. Where did you find them??? The ones I got are steel and i found them on amazon search "shaft collar" on google it took me forever to figure out what they are called Quote Link to comment
OpelWagenGT Posted February 12, 2010 Author Report Share Posted February 12, 2010 so now that the front suspension is all cleared up, any suggestions about lowering blocks where I can find them. I really would rather buy a complete kit than buy blocks and have custom u bolts made or anyting like that. Quote Link to comment
ariascarlos1990 Posted February 12, 2010 Report Share Posted February 12, 2010 any Schucks, Autozone, Baxters should have them. Quote Link to comment
Guest DatsuNoob Posted February 12, 2010 Report Share Posted February 12, 2010 Got my whole 3" block kit from Autozone, was quite reasonable, and easy to install. Quote Link to comment
Guest kamakazi620 Posted February 12, 2010 Report Share Posted February 12, 2010 If you want a kit for the back check out http://www.speedwaymotors.com/ProductSummary.aspx?free_text|2/12/2010%205:35:20%20AM=Lowering+blocks&deptId=0 Whole kits for under $40 bucks I've used them and thier Nice Quality :D Quote Link to comment
OpelWagenGT Posted February 12, 2010 Author Report Share Posted February 12, 2010 If you want a kit for the back check out http://www.speedwaymotors.com/ProductSummary.aspx?free_text|2/12/2010%205:35:20%20AM=Lowering+blocks&deptId=0 Whole kits for under $40 bucks I've used them and thier Nice Quality :D thanks for your help it's much appreciated I will check both of these as autozone is close to my house so it might be nice to pick some up if I can. Quote Link to comment
OpelWagenGT Posted February 13, 2010 Author Report Share Posted February 13, 2010 so I did even more researching and I could not find a lowering block kit with u-bolts that were for an axle smaller than 3 inches in diameter. Quote Link to comment
ariascarlos1990 Posted February 13, 2010 Report Share Posted February 13, 2010 Just measure your u-bolts then go into the parts store and measure one from each kit to find your correct bend. they should have them on display. Quote Link to comment
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.