jonahsturdy14 Posted April 23, 2014 Report Share Posted April 23, 2014 So i have done all the reading and know that 280zx struts give a 510 bigger brakes,and and option for lower car but i have been told by one person that is actually pulls the wheels in half an inch on each side, is that true Quote Link to comment
datzenmike Posted April 23, 2014 Report Share Posted April 23, 2014 No, I think it's more like 3/4" Quote Link to comment
HRH Posted April 23, 2014 Report Share Posted April 23, 2014 It does narrow the track. Here's an interesting tidbit. You could use 810 front struts. The downside is finding good brake pads and rotors for that combo (or brake pads at all) is a little hard. However, special order through NAPA or Hawk pads will work. BUT, be warned, that will increase the track width to likely past your fenders. Sawzall and flares will solve that. Quote Link to comment
yellowdatsun Posted April 23, 2014 Report Share Posted April 23, 2014 This should be in the 510 section.....but, yes, it does narrow the front track. I always thought it was a half inch, but maybe it's 3/4. Somewhere in that range though. Keep in mind you need to either modify the perch, or cut it off. Quote Link to comment
Laecaon Posted April 23, 2014 Report Share Posted April 23, 2014 It does NOT narrow the track width. It narrows the WMS(Wheel mount surface) to WMS distance. It allows for more negative offsets which in turn will keep original track widths. Track width being center of tire to center of tire. 1 Quote Link to comment
67_1600 Posted April 23, 2014 Report Share Posted April 23, 2014 It does NOT narrow the track width. It narrows the WMS(Wheel mount surface) to WMS distance. It allows for more negative offsets which in turn will keep original track widths. Track width being center of tire to center of tire. But all else being equal, yes they will narrow your track width. I think a lot of people who do the swap are in the same boat I was - I liked how my car looked with the wheels I had and was concerned about the narrowed track width. I didn't go into it thinking 'oh goody, now I can buy some new rims to compensate for the narrowed width' but maybe I'm the exception more than the rule. Quote Link to comment
Jesse C. Posted April 23, 2014 Report Share Posted April 23, 2014 Most folks that switch struts and are running wide rims, with a zero offset, always end up using spacers to move the rim away from the strut. Just a warning so you are not caught off guard. Quote Link to comment
jonahsturdy14 Posted April 23, 2014 Author Report Share Posted April 23, 2014 Thanks everyone for the help, i was hoping the narrow the track width was true. and im still new here and i had no idea i posted this not in the 510 section Quote Link to comment
KlassicMotion Posted April 24, 2014 Report Share Posted April 24, 2014 No, I think it's more like 3/4" It's a half inch. I've seen other people say 3/4" on here, but not in my findings. Maybe it has to do with different years? The black hub on the left is a Z31, I'm not sure what the second hub is on the left (I was told it is a Z31 as well), '71 510 middle, 1982 280zx on the right. There is a half inch difference between the Z31 and 280zx. The 510 is just shy of 1/2". Pics with unknown hub: Quote Link to comment
ggzilla Posted April 24, 2014 Report Share Posted April 24, 2014 It is exactly 15mm. Quote Link to comment
datzenmike Posted April 24, 2014 Report Share Posted April 24, 2014 0.5910" then... closer to 0.6" than 0.5" Quote Link to comment
izzo Posted April 24, 2014 Report Share Posted April 24, 2014 omg you can put zx struts on a 510? 3 Quote Link to comment
blue72 Posted April 24, 2014 Report Share Posted April 24, 2014 Also, if you for some reason decide to use the ZX steering arms, then it'll pull the wheels in an additional 3/8" per side. Quote Link to comment
ggzilla Posted April 25, 2014 Report Share Posted April 25, 2014 Good point - the toe-in must be adjusted once struts are changed. Quote Link to comment
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.