bbqbill Posted December 2, 2011 Report Share Posted December 2, 2011 i keep reading about rolled fender flaiers,and want to know how to do it. is there a thread,or maybe a video how to? ive seen some pics,and like the look .any help Quote Link to comment
Zfighter76 Posted December 2, 2011 Report Share Posted December 2, 2011 yes, you can roll the stock inner lip on your fenders to eliminate the sharp inner fender cutting the sidewall of your tire when you lower you car. you cal achieve more of a flared look by pulling your fenders. these both can be achieved by using a fender roller or a baseball bat as the crude option. for the pull you may want to make relief cuts in the fender to allow it to stretch out more and then fell the cuts with sheet metal and body filler to smooth it out. heres a rolled fender lip, see how theres no sharp edge to slice your sidewalls?this is a pulled fender, i cant find a good example and this looks like shit but you get the point. Quote Link to comment
Zfighter76 Posted December 2, 2011 Report Share Posted December 2, 2011 for baseball bat method, just heaat up fender arch area if you care about your paint with a heat gun, and stick the bat in there and roll it so it bends the inner lip up. not very much visable differance on the outside with this method. Quote Link to comment
Xander_42 Posted December 2, 2011 Report Share Posted December 2, 2011 One issue you may be having is that you are asking about rolled fender flares. Most fender flares do not need to be rolled because they already have a narrow edge for good wheel clearance. You want to roll the stock fender lip. (Just some badly worded clarification) This is a fender roller: They're expensive (~270), so what I recommend doing is finding someone that has one you can borrow or rent or pay to have used. The people that would be most likely to have one would be any shops that do proper race car preparation, maybe an autocross club, and maybe any shops that do a lot of hella-flush crap. With the shops you'd probably need to pay them, but if there's an autocross club, they may have one you could rent or borrow. I mean a club for autocrossers, not a club that runs autocrosses. Originally posted by Skib: Bat method: Quote Link to comment
Peter_Pablo Posted December 2, 2011 Report Share Posted December 2, 2011 look what we done in my case with my fenders http://www.youtube.com/watch?v=IjHs8dBb8M8&feature=g-upl http://www.youtube.com/watch?v=TZZZql_PWEE&feature=g-upl 1 1 Quote Link to comment
1lo620 Posted December 2, 2011 Report Share Posted December 2, 2011 look what we done in my case with my fenders http://www.youtube.com/watch?v=IjHs8dBb8M8&feature=g-upl wow, better you than me, I much rather go rent one of those nifty little tools and do it correctly, alot of risk in using a steel bar... 1 Quote Link to comment
Skib Posted December 2, 2011 Report Share Posted December 2, 2011 wow, better you than me, I much rather go rent one of those nifty little tools and do it correctly, alot of risk in using a steel bar... I wouldnt say that, Iv done it with bars and baseball bats with no issues. 3 Quote Link to comment
1lo620 Posted December 2, 2011 Report Share Posted December 2, 2011 didnt say it couldnt be done, it obviously can be done....just be easier with that tool...that is all I ment..! I say do what you want to do....!!!!!! 1 Quote Link to comment
Skib Posted December 2, 2011 Report Share Posted December 2, 2011 just be easier with that tool... lol this is most likely true :lol: Iv always done it the ghetto way, never used the fancy tool before. 1 Quote Link to comment
Peter_Pablo Posted December 2, 2011 Report Share Posted December 2, 2011 that´s the reason why use ghetto tools because i woudnt find the nifty tool here and youtube it so educative now Quote Link to comment
Xander_42 Posted December 2, 2011 Report Share Posted December 2, 2011 just be easier with that tool...that is all I ment I'm actually not sure, I think the tool would not be easier, but I think it would probably produce a better product. Less likely to damage the paint because of the rubber roller. More able to get the fenders rolled to exactly where you want them. But, I think whatever method is fine, so do what you want. 1 Quote Link to comment
bbqbill Posted December 4, 2011 Author Report Share Posted December 4, 2011 for baseball bat method, just heaat up fender arch area if you care about your paint with a heat gun, and stick the bat in there and roll it so it bends the inner lip up. not very much visable differance on the outside with this method. your right,i do want the flair look not a rolled lip.im getting as much info on the things i want to do to my truck from people who best !!! thanks for the tips i will post pics when i start the work ,cant wait. Quote Link to comment
Farmer Joe Posted December 4, 2011 Report Share Posted December 4, 2011 i did the same thing on my truck, just with a smaller piece of plumbing pipe.. i understand they make a took for it, but i dont buy tools that really only have one job... i like multitasker tools.. like plumbing pipe... lol hella flush? 1 Quote Link to comment
Zfighter76 Posted December 7, 2011 Report Share Posted December 7, 2011 i did the same thing on my truck, just with a smaller piece of plumbing pipe.. i understand they make a took for it, but i dont buy tools that really only have one job... i like multitasker tools.. like plumbing pipe... lol hella flush? yes, hella flush. 1 Quote Link to comment
Creepy Cruiser Posted December 7, 2011 Report Share Posted December 7, 2011 One issue you may be having is that you are asking about rolled fender flares. Most fender flares do not need to be rolled because they already have a narrow edge for good wheel clearance. You want to roll the stock fender lip. (Just some badly worded clarification) This is a fender roller: They're expensive (~270), so what I recommend doing is finding someone that has one you can borrow or rent or pay to have used. The people that would be most likely to have one would be any shops that do proper race car preparation, maybe an autocross club, and maybe any shops that do a lot of hella-flush crap. With the shops you'd probably need to pay them, but if there's an autocross club, they may have one you could rent or borrow. I mean a club for autocrossers, not a club that runs autocrosses. We have one of these and they work killer. If you take your time, you can easily widen a fender 1.5"-2" (and even more if you need), without damaging the paint (the trick is to use a heat gun to keep the paint soft). There is a learning curve and it's not fast to do it correctly (20-30 minutes per fender), but the results are great. It does how ever have one major drawback, and that is, it doesn't fit a 6 bolt pattern. We are making an adapter for ours. Quote Link to comment
Dr. Scagpoople Posted December 7, 2011 Report Share Posted December 7, 2011 i did the same thing on my truck, just with a smaller piece of plumbing pipe.. i understand they make a took for it, but i dont buy tools that really only have one job... i like multitasker tools.. like plumbing pipe... lol hella flush? Dude, I drive by this truck a few times a month going to visit my friend. I always look forward to seeing it on my way. Quote Link to comment
Xander_42 Posted December 8, 2011 Report Share Posted December 8, 2011 It does how ever have one major drawback, and that is, it doesn't fit a 6 bolt pattern. We are making an adapter for ours. Did not think about that. Good point. 1 Quote Link to comment
Creepy Cruiser Posted December 8, 2011 Report Share Posted December 8, 2011 I didn't either, until we went to bolt it up to the first truck we were going to use it on, lol. 1 Quote Link to comment
Radim Posted December 21, 2011 Report Share Posted December 21, 2011 My 620, 11" wheels rolled and slightly flared fenders. 1 Quote Link to comment
Lee R Posted December 21, 2011 Report Share Posted December 21, 2011 How did you lower you rear? Your leafs don't have much arch in them...pretty straight. Looks perfect! Quote Link to comment
bbqbill Posted December 22, 2011 Author Report Share Posted December 22, 2011 so witchway did you use for your flairs? your truck made me want to do this. Quote Link to comment
Radim Posted December 22, 2011 Report Share Posted December 22, 2011 Blocks and 4x4 720 leafs I used a fender roller with 139.7-6H to 114.3-5H adapters... Which is why it looks cleaner than a baseball bat. :) 1 Quote Link to comment
bbqbill Posted December 25, 2011 Author Report Share Posted December 25, 2011 thanks, i just need to find one in my area . Quote Link to comment
GERMS Posted November 24, 2012 Report Share Posted November 24, 2012 Blocks and 4x4 720 leafs I used a fender roller with 139.7-6H to 114.3-5H adapters... Which is why it looks cleaner than a baseball bat. Hey radim maybe one day when I'm in the area you can do my wheel wells like yours, how much for the job? Looks great! Quote Link to comment
ohmrchristopher Posted January 16, 2013 Report Share Posted January 16, 2013 Im going to dig up this old one rather then making a new post. I like clean boards. So is rolling the fender the way to go or what about cutting/bolt-on flares. If you havent seen my truck, check my sig. Anyways I am getting ready for summer and what to mount my 15x10". I plan on a 225/60 tire and like my ride height, might go lower. I have seen trucks with bolt-ons and rolled, either way I am causing damage/misform to the body. I dont plan on a glass restore, I like the ratty look, thus why I bought it in its condition. I think I was going to attempt to roll the fenders and if it didnt work, cut out the metal and install the bolt-ons. I would also try the front fenders first because RockAuto sells replacements, I am more worried about the box. The thing that bothers me is the reverse lip and having to hammer/form that out flush and then pull it out too. Its not like its a flat fender to begin with. Quote Link to comment
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.