Charlie69 Posted September 5, 2016 Report Share Posted September 5, 2016 I have done several of the mounts over the years and each one was a little different in measurement. They would very between an 1 7/8" to 2 1/16" I believe this could be do to the worn mounts that I was working with. 1 Quote Link to comment
]2eDeYe Posted October 6, 2016 Author Report Share Posted October 6, 2016 Transmission brackets are out to the laser cutter. Hope to get a good turn around on them and we'll get to see how they fit soon. In other news, I have been working one of our members on SR20 mounts for the L series 521, part of that will be a trans mount for the SR transmission.This also allows me to design SR20 mounts for the 620 as well. Will need some guys for test fitting, but I will start another thread for that process when those get welded up. 2 Quote Link to comment
EastBay521 Posted November 9, 2016 Report Share Posted November 9, 2016 So when can I order mine? Some one was fortunate enough to pick up a ka 1 Quote Link to comment
]2eDeYe Posted November 9, 2016 Author Report Share Posted November 9, 2016 Still waiting on the laser cutter for the final test pieces. 1 Quote Link to comment
]2eDeYe Posted November 29, 2016 Author Report Share Posted November 29, 2016 3 Quote Link to comment
Charlie69 Posted January 1, 2017 Report Share Posted January 1, 2017 The mount is looking good. Hows is the angle of the motor front to back with your front and rear mounts installed. Should try to keep stock. When I build mounts I level the carb mounting surface on the intake. Quote Link to comment
]2eDeYe Posted March 17, 2017 Author Report Share Posted March 17, 2017 I have a run of these powder coated and ready to ship. Keep in mind that the transmission mount is designed for the 31" long 5-speed from the 720 or hardbody. 1 Quote Link to comment
]2eDeYe Posted March 17, 2017 Author Report Share Posted March 17, 2017 The mount is looking good. Hows is the angle of the motor front to back with your front and rear mounts installed. Should try to keep stock. When I build mounts I level the carb mounting surface on the intake. It's about 5deg or so at the trans mount. The intake plenum should be just about level 1 Quote Link to comment
Charlie69 Posted May 20, 2017 Report Share Posted May 20, 2017 Those are prettier than mine, but how much for a set? LOL Quote Link to comment
]2eDeYe Posted May 20, 2017 Author Report Share Posted May 20, 2017 Those are yours, I am pretty sure. lol They are $150 if you don't win a set. 1 Quote Link to comment
Charlie69 Posted May 20, 2017 Report Share Posted May 20, 2017 Just teasing Redeye!!! LOL You did a great job designing these. 2 Quote Link to comment
uberkevin Posted May 29, 2017 Report Share Posted May 29, 2017 So your tranny mount doesn't work with the 240sx? Or I'm I stupid. Like normal. 1 Quote Link to comment
Charlie69 Posted June 2, 2017 Report Share Posted June 2, 2017 240 SX has a longer transmission. I ran into this a couple decades ago. Not sure if the engine mounts are the same as the truck KA24. 1 Quote Link to comment
]2eDeYe Posted June 2, 2017 Author Report Share Posted June 2, 2017 The 240SX trans requires floor modifications and the truck I was test fitting with has not had a final drive train selected. If someone was to use my motor mounts and run the 240sx trans I could use some measurements. :) 1 Quote Link to comment
]2eDeYe Posted June 2, 2017 Author Report Share Posted June 2, 2017 240 SX has a longer transmission. I ran into this a couple decades ago. Not sure if the engine mounts are the same as the truck KA24. The motor mounts are the same between the 240 and the truck on the block. 1 Quote Link to comment
uberkevin Posted June 5, 2017 Report Share Posted June 5, 2017 The 240SX trans requires floor modifications and the truck I was test fitting with has not had a final drive train selected. If someone was to use my motor mounts and run the 240sx trans I could use some measurements. :) If you happen to send some my way I'll see about getting some measurements. And see how different they may be then mine. 1 Quote Link to comment
]2eDeYe Posted June 5, 2017 Author Report Share Posted June 5, 2017 Will you be at Canby? 1 Quote Link to comment
uberkevin Posted June 5, 2017 Report Share Posted June 5, 2017 I unfortunately had to use the last of my time off for a wedding a few weeks ago. So. No Canby for me. 1 Quote Link to comment
uberkevin Posted June 6, 2017 Report Share Posted June 6, 2017 But maybe if you gave them to Dmike he could bring them to flatcats and I could pick them up there. I'd send them back if I didn't wanna keep them of course. I'll ask him if he'd do something like that first. 2 Quote Link to comment
]2eDeYe Posted June 6, 2017 Author Report Share Posted June 6, 2017 Just let me know. :) 1 Quote Link to comment
uberkevin Posted June 6, 2017 Report Share Posted June 6, 2017 I asked Dmike. I'll let you know. 1 Quote Link to comment
datzenmike Posted June 6, 2017 Report Share Posted June 6, 2017 Yeah, I'm OK with that. See you at Canby Steve. 2 Quote Link to comment
uberkevin Posted June 6, 2017 Report Share Posted June 6, 2017 Thanks Mike. And Redeye. 3 Quote Link to comment
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.