dat521gatherer

As in the previous photo it is good to drill a hole and put a wire in them. After the plastic sleeves wear off the chains will jump off the truck when going over bumps and fall in between the gate and bed hitting the road never to be seen again. I've caught mine a few times with just one hook attached. some 320 chains just for fun.

BIG THANKS to Ericsb210 for the parts.

Thanks for the parts Eric and Redbanner!! New list of parts wanted. Rubber muffler hanger and ubolt. cant find correct ubolt at the parts store.--Got Auto shift knob-minty Coat hangers--Got Locking fuel door Trunk rug Battery hold down Tach Clock Thermostat housing non smog More important stuff Left lower door hinge. Grey left horn button with springs and screw. Long heater hose. Factory only I have a chopped up ghetto mess! nla from nissan. Auto trans speedo gear. any idea at least on the part number? Tail pipe. Might go to a muffler shop but they usually wanna replace the whole system. Battery hold down, I may go after market on this.

Pam says thank you for the relay and light switch.

You can take the cover off and look at the points. All the ones I've looked at looked new. you can adjust them to make your headlights brighter but as far as I've read nobody does that. Great idea for A project and write up for someone to do. Some suggest buying the solid state rather than the point type. I prefer the points type. As far as interchange you can click on the also fits tab on oriellyauto.com when looking at the part. Here is how to adjust in the 521 body and chassis pdf. http://www.olddatsuns.com//620tech.htm

hard to see you may need to save the pic and enlarge it. there is a black piece of plastic in between the bracket and cylinder.

I have one. single headlight version 1966 only and some have been seen on early 1967's. the condition is good but it needs to be rechromed. let me know if your interested.

Thats only for the brake and clutch. The gas pedal is a different size. If you look in a owners manual you'll see no gas pedal pad in the pics nor the brochures. I've tried to squeeze one on the gas pedal and you have to cut a slot in the bottom of the pad and it still doesn't work.

Rebuilt left horn button broken tabs, cleaned contacts, fixed wire lubed sun visor shaft so the plastic mount doesnt break. It was super stiff lubed door hinges lubed seat rails fuel filter replaced ordered hatch shocks-o'rielly auto ordered wheel center caps-les schwab ordered hood hinge seals-nissanparts.cc ordered hood rod holder clip-nissanparts.cc ordered dome light-nissanparts.cc 720 rear view mirror installed. gotta love that universal ball on the back of most datsuns. unplugged wiper squirter

I'm looking for these parts for my 75 b210 or original part numbers. fusebox, used is fine no cover needed hood bumpers 2 of them, used is fine. The ones on ebay aren't correct. Horns needed really bad. 1 high 1 low, used is fine coil boot I'll pay with paypal/cash/money order. I got all of this stuff, thank you and please scroll down for other parts I need.

The 521 never came with a gas pedal pad.

here is one for reference. dont mind the tape on it. I would take measurements but its in storage. I can get them later this week if you need.

It did look like something was missing out of the anti dieseling solenoid when I took it out. I'll try cleaning out the needles under the caps under the bowl and maybe replacing the accelerator pump, the boot is old and cracking.

I need a anti dieseling solenoid. The wire is not repairable. Can I use one off my l16 hitachi dhc328? or dhc340? I cant find the part numbers to compare. It does idle fine without it hooked up. I'm hoping a anti die-sol will fix the flat spot it has when stepping on the gas lightly. I'll also clean out the 2 jets under the bowl. My choke wire has no power. Where is the choke relay? Is it under that mysterious black box next to the coil? I cant find its location in my manual. How important is the throttle opener system? Mine is disconnected and the servo diaphram hose is going to the bottom of the carb instead of the throttle opener solenoid. should I leave it like this meaning does it work being there or can I remove the throttle opener system as in the control valve and solenoid?

Ok I bought the haynes and chilton manual. The factory nissan is on the way in the mail. THINGS TO DO- 1 Lube door hinges. One has a bad flat spot that makes the door not want to shut. lube now fix later.---Done 2 Fix the horn. I hear the relay and a faint sound from the horn. steering wheel contacts?---fixed, bought horns--Done 3 Muffler is rattling. Should I remove the cat if its there?---no cat but has a pre muffler.---Done 4 Gauges work sometimes, probably a loose con. I dont see a gauge volt reg on the back cluster.---Done 5 Check timing and dwell---Done 6 Unplug left wiper squirter---Done 7 Study and reroute vacuum lines. lots of missing and blocked lines.---Done 8 Study and fix carb wires.---swapped 4 weber---Done 9 Fix flat spot in carb---swapped 4 webber---Done 10 Shine rims and find center caps to buy---Done THINGS TO BUY--- 1 Dome light with housing---Done 2 Rear view mirror---Done 3 Rear hatch shocks.---Done 4 Heater hose---need long one really bad---Done 5 Fusebox---bought 6 Brake booster 7 Rear shocks---Done 8 Find a stock fm radio---Done 9 Hood bumpers---Done 10 Left tail light---Done 11 Owners manual---Done 12 Coil boot---Done Specific pics and questions coming soon. Thanks guys.

Yeah she wont be driving it by herself anytime soon. Only with mom or dad in the car. At this point the datsun bug has bit my wife with this car. They just went up to the car wash and they bickered and my wife won. She wants to drive it to work already. Besides, insurance for her to drive it by herself is way too expensive.

a/c. It doesnt work and I'm not sure it ever will considering it takes the old refrigerant.

I tried highlighting and printing selected. It only printed one header address line with a page number. I tried clicking the print button at the bottom of the page and it just opens a blank page? I'm using firefox. I tried clicking the save button and opening that and I get the same blank page. I tried saving it and opening file containing folder and printing but it prints out in a different page style.

My wife and I bought this the other day. I'm still test driving it to see what bugs need to be worked out. We bought it so our daughter can get some driving experience but it's growing on us adults quickly. The to do list will be posted soon with lots of questions. all comments and help welcome. Let the PICS begin.

This is the first time I've had all 3 together.

Nice. Hey wait thats not my 521 I wanted is it? :angry: It's all good just teasin. :console:;)

I'll take 2 bottom left. PM me your paypal.

I really need this seal. This picture of the after market rubber ones on ebay dont work for me. I need nos felt style. Please let me know if you can find some. I'm saving money to buy other parts. :)

BAD ASS!!