xavier Posted February 1, 2017 Report Share Posted February 1, 2017 I'm new here and I been reading all topics regarding the issues that I have with my truck, they been very helpful. I need help on a fuel gauge problem , the situation is this , when truck is on the key off position or no key at all, the fuel gauge shows full tank, but when I turn the key on , fuel gauge start dropping and goes to empty, I did the grounding at the tank on yellow wire nothing change , I installed new ground at the tank but no change yet , please help someone. Quote Link to comment
banzai510(hainz) Posted February 1, 2017 Report Share Posted February 1, 2017 if possibel reach under the instrument panel and reseat the connecter, clean the contack on the sender. Quote Link to comment
wayno Posted February 1, 2017 Report Share Posted February 1, 2017 What is the temp gauge doing, same thing, is it full hot when key is off? Quote Link to comment
datzenmike Posted February 2, 2017 Report Share Posted February 2, 2017 Can't be a stock fuel gauge. It sould read empty with the key off. If you have the stock gauge reading full with the key off then it's getting power when it shouldn't and no power when it should. Quote Link to comment
Diego Zuniga Posted March 1, 2017 Report Share Posted March 1, 2017 I am having fuel gauge issues as well. It was working fine and now reads full when truck is on no matter how much fuel is in it and and goes down to E when I shut truck off. The temp gauge is still working like it should. Any suggestions? Quote Link to comment
datzenmike Posted March 1, 2017 Report Share Posted March 1, 2017 Somewhere between the gauge and the sender in the tank the wire is grounded. Full is 10 ohms or less, grounded is 0 ohms so FULL reading. Even the sender in the truck could be stuck in the full up position. Disconnect the Yellow? wire at the tank. If is drops to EMPTY the sender is stuck. If it doesn't move from FULL it's touching ground somewhere between there and the gauge. Quote Link to comment
Diego Zuniga Posted March 3, 2017 Report Share Posted March 3, 2017 Awesome I will check. Thanks for the help. Quote Link to comment
Diego Zuniga Posted March 9, 2017 Report Share Posted March 9, 2017 The gauge did not drop when I unhooked the yellow wire. Any idea where I can check for a ground issue? Or any chance it could be a gauge issue? 1 Quote Link to comment
DanielC Posted March 9, 2017 Report Share Posted March 9, 2017 There are two connectors low on the firewall, by the starter, that connect the engine room wiring harness to the bed harness. Unplugging the six pin connector, with the yellow wire will disconnect the fuel gauge wiring from the bed harness. See if unplugging that connector causes the gauge to drop. 1 Quote Link to comment
Diego Zuniga Posted March 10, 2017 Report Share Posted March 10, 2017 I unplugged the plug and the gauge did drop to E. I cleaned the plug with electrical cleaner and a wire brush. Is there anymore test I can do to narrow it down? Quote Link to comment
DanielC Posted March 10, 2017 Report Share Posted March 10, 2017 Normal fuel gauge operation: Gauge reading full, there is low resistance between the instrument panel connection for the fuel gauge and ground. It could at the fuel tank, if the sender or sender wire is shorted to ground, or more likely the tank is full. As gas is used up, the fuel gauge sender adds resistance to the connection between the yellow wire, and ground. And then the fuel gauge moves toward empty. When the key is off, the gauge should drop to empty. Are you sure the gauge shows full with the key off? You need a test light for the following fuel gauge wiring tests: With the connector by the starter unplugged, turn the key on. The fuel gauge should stay at empty. Make sure no tail lights are on. With the key on, the wire going to the reverse light switch is also hot. The reverse light switch wire is red with a black stripe. Shorting this wire to ground will blow the fuse for the reverse light circuit. If you take a test light, and ground one connection to the test light, and touch the yellow wire, the test light should flash on and off, this is normal. If the test light is flashing, the fuel may read somewhere about half range. This too is normal. If you can make the yellow wire short to ground, the fuel gauge should go to full. If the fuel gauge does act the way I described, the fuel gauge and wiring to the connector by the starter is probably good. Reconnect the bed and engine room wiring harness wires. Lift the cover over the gas tank, in the bed of the truck. Redo the tests you did on the yellow wire, at the connector, by the starter, at the yellow wire by the gas tank. Does the test light flash like it did at the connector by the starter? Does the fuel gauge go to the same place it did when you made the connection by the starter? Does the fuel gauge go to full if you ground the yellow wire to the frame of the truck? Make sure you have good connection through any paint, rust, dirt and grime. If all these test act like I described, the fuel gauge sender in the tank may be giving you a problem. Quote Link to comment
Diego Zuniga Posted March 10, 2017 Report Share Posted March 10, 2017 The gauge does drop to empty when the key is off, and reads past full when you turn the key on. Should I try your test you recommend still? Or am I looking at a different issue? Quote Link to comment
DanielC Posted March 11, 2017 Report Share Posted March 11, 2017 Once again, the sender in the tank has very low resistance to ground when the tank is full. If the tank is full, the fuel gauge sender shorts the yellow wire to ground. Disconnect the yellow wire at the tank. When you do this, the gas gauge should go to empty, with the key on. If the gauge does NOT go down when you disconnect the yellow wire, disconnect the plug by the starter. If the gauge then goes down with the key on, the yellow wire is shorted to ground between the plug by the starter, and the fuel tank sender connection. 1 Quote Link to comment
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.