jboulukos Posted May 1, 2016 Author Report Share Posted May 1, 2016 Thank you for the information regarding the fail safe thermostats...I plan to get a regular 180F thermostat. Here's a list of the parts I will replace. -cylinder head gasket -water outlet gasket -thermostat -exhaust and intake gasket Is there anything else I need or should replace with this head job? Is there a thermostat gasket/any other gaskets? Quote Link to comment
jboulukos Posted May 1, 2016 Author Report Share Posted May 1, 2016 Newest Photo Quote Link to comment
datzenmike Posted May 1, 2016 Report Share Posted May 1, 2016 When you take the thermostat out you will see it has a gasket. Clean the mating surfaces and put gaskets on dry. Quote Link to comment
jboulukos Posted May 1, 2016 Author Report Share Posted May 1, 2016 Excellent Is the thermostat gasket made of rubber? Quote Link to comment
Lockleaf Posted May 1, 2016 Report Share Posted May 1, 2016 No. On these datsuns it's another paper style gasket. 1 Quote Link to comment
datzenmike Posted May 1, 2016 Report Share Posted May 1, 2016 Hell I cut them from cereal boxes. 1 Quote Link to comment
jboulukos Posted May 1, 2016 Author Report Share Posted May 1, 2016 I know the gasket on the right is for the water outlet. Is the gasket on the left to go between head and thermostat? Quote Link to comment
jboulukos Posted May 1, 2016 Author Report Share Posted May 1, 2016 Thanks! What are the lower 2 gaskets seen here? It came with the exhaust and intake gasket I ordered. Might be only used on 79-82 but not certain. Quote Link to comment
B210GX Posted May 1, 2016 Report Share Posted May 1, 2016 I know the gasket on the right is for the water outlet. Is the gasket on the left to go between head and thermostat? No, one is for an A13, A15 some A14's without the EGR head and the other is for an A14 with the EGR Order the one on the right, It will fit either, just cut the excess off to fit.. they are both for the thermostat Then the two lower gaskets are for the heat riser manifolds, where the two manifolds are bolted together.... Im not gonna go look for pics SEARCH 1 Quote Link to comment
jboulukos Posted May 2, 2016 Author Report Share Posted May 2, 2016 Ok thanks. So I removed the thermostat...had "Nissan" on it so it might be original to the car. I took off the rocker assembly and then did the loosening sequence on the head bolts. Took them off. Now my main question is how to remove the head from the car...with manifolds and carb attached? I took off the top screws to the manifolds however the lower screws are difficult to get to. I'm excited to remove the head and examine it. Quote Link to comment
jboulukos Posted May 2, 2016 Author Report Share Posted May 2, 2016 Is the exhaust pipe attached to the manifolds? Quote Link to comment
jboulukos Posted May 2, 2016 Author Report Share Posted May 2, 2016 Here's the push rods and head bolts in order. Quote Link to comment
jboulukos Posted May 2, 2016 Author Report Share Posted May 2, 2016 What is this metal bracket attached to the passenger side of the cylinder head? Quote Link to comment
jboulukos Posted May 2, 2016 Author Report Share Posted May 2, 2016 Head bolts off. Now how to lift out the head with manifold and carb...do I detach the exhaust pipe? If so, how? Quote Link to comment
jboulukos Posted May 2, 2016 Author Report Share Posted May 2, 2016 No, one is for an A13, A15 some A14's without the EGR head and the other is for an A14 with the EGR Order the one on the right, It will fit either, just cut the excess off to fit.. they are both for the thermostat Then the two lower gaskets are for the heat riser manifolds, where the two manifolds are bolted together.... Im not gonna go look for pics SEARCH True story! I pulled the thermostat out today. There is no gasket between thermostat and cylinder head, as you've stated. There is only the water outlet gasket. Quote Link to comment
Lockleaf Posted May 2, 2016 Report Share Posted May 2, 2016 Undo the exhaust piping from the bottom of the exhaust manifold. That will allow you remove everything as a set. That bracket you took a pic of is for attaching an engine hoist to hook the engine and pull it out. 1 Quote Link to comment
jboulukos Posted May 2, 2016 Author Report Share Posted May 2, 2016 Excellent. So I will undo the exhaust pipe and pull it out by hand. Then remove the manifolds from the head. Next, clean the block, bolt holes, cylinder head surface. Then have the head examined and pressure tested. Put gasket on and reassemble. I know the torque specs for head bolts, manifold nuts, rocker arm assembly. And I know the valve clearance measurements, cold and hot. Are there torque specs for the water outlet or just tighten snug with a wrench? Quote Link to comment
jboulukos Posted May 3, 2016 Author Report Share Posted May 3, 2016 Help. I detached the exhaust and I was just about ready to lift the head with the manifold/carb together when I realized there is one more attachment. It's a small metal cable with rubber hose around it that screws into the firewall and goes to the backside side of the carb. How can I detach this? Quote Link to comment
jboulukos Posted May 3, 2016 Author Report Share Posted May 3, 2016 I ended up leaving the carb inside and taking the manifold and head out. Pictures to come. Quote Link to comment
jboulukos Posted May 4, 2016 Author Report Share Posted May 4, 2016 Pulled off the gasket and found that it was compromised on the last cylinder. The corresponding cylinder did not have water inside but had a slightly different color than the others. Does this look like a classic blown head gasket? Quote Link to comment
jboulukos Posted May 4, 2016 Author Report Share Posted May 4, 2016 The gasket mating surfaces were scraped with clean razor blades and wire brushed. Quote Link to comment
jboulukos Posted May 4, 2016 Author Report Share Posted May 4, 2016 On previous threads I have read to spray the gasket mating surfaces with ether/starter fluid. Is this appropriate? Quote Link to comment
Lockleaf Posted May 4, 2016 Report Share Posted May 4, 2016 Using starter fluid is just an angry cleaning solution. You can use brake clean or whatever as well. And yes, that looks like a pretty classic head gasket issue. It almost looks like the gasket was misaligned when last installed, but that may be totally incorrect. Nice work man! 1 Quote Link to comment
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.