Ratsun, I need your help.

[squatches]

No sir...

They just now opened a "pick-n-pull" in greenville and they dun hav any

 

 

 

where are you located besides skyrim lols, i may be able to bring you one if i have it

[metalmonkey47]

Squatches don't get him too excited bro :thumbup:

[squatches]

Squatches don't get him too excited bro :thumbup:

 

 

haha if all else fails i can pull one out of my l20s i have stashed

[Dat Lurka]

too late

Excited

[Sealik]

Warped head

The bottom of the head was only shaved ?....correct?

Well....if you have a banana and the bottom is shaved to straighten it out....what about the top where the cam towers sit?

Needs to be shaved also or the towers shimmed

Correct?

[Eagle_Adam]

if theres someone in portland with one they will donate ill ship it.

[Dat Lurka]

Warped head

The bottom of the head was only shaved ?....correct?

Well....if you have a banana and the bottom is shaved to straighten it out....what about the top where the cam towers sit?

Needs to be shaved also or the towers shimmed

Correct?

 

If it was that bad then I should have had problems before I took it off. Shop said everything was straight.

I think squatches has me covered. He's right up the road.

I found a fuckup. #3 cam tower dowel seemsto be the wrong one. It was on the back and I couldn't see it. Probably that half a milimeter difference it takes to snap a cam :blush:

I shaved it down and it's nice and snug now.

Just like dropping the tensioner

I won't do it again.

[Sealik]

If it was that bad then I should have had problems before I took it off. Shop said everything was straight.

I think squatches has me covered. He's right up the road.

I found a fuckup. #3 cam tower dowel seemsto be the wrong one. It was on the back and I couldn't see it. Probably that half a milimeter difference it takes to snap a cam :blush:

I shaved it down and it's nice and snug now.

Just like dropping the tensioner

I won't do it again.

 

Not what you said yesterday..............

 

 

Dat Lurka

 

Got my head back. The shop lady told me it wasen't a head but actually an aluminum banana. Shaved 10 thousandths. Had two burn valves. Apparently it's been off in the past. #2&3 intake valve seats are stainless steal.

Yesterday, 05:06 PM

[Dat Lurka]

They said it was straight when they were done with it :rofl:

:poke:

[Dat Lurka]

Squatch to the Rescue!

Looks like it's gonna be ok.

[CFHdatsun77]

I thought riften was in the southeastern province of skyrim...

Ha i was Going to make a Skyrim Joke but didnt think anyone Would Get it. :rofl:

[Phixius]

Ha i was Going to make a Skyrim Joke but didnt think anyone Would Get it. :rofl:

 

Huh? ;)

 

 

....ive got parts datlurka, but im in the northwest. Hope your deal works out...

 

How was the ride on horse back/carriage or travel by foot? Or you got dragons?

 

...Dont overload with shit, it makes it extreamly hard to move...

[Dat Lurka]

It's all good.

Cam is on the head.

Still need a torque wrench.

[mike]

Did you snap that during assembly/ prior to bolting on the head? How in the fuck???

 

Check this link... L series torque specs :)

http://www.davidcmur...20tech4.htm#TS2

 

 

Roll the engine over by hand after you get it torqued down and the chain set to make sure nothing is binding.

[Dat Lurka]

Did you snap that during assembly/ prior to bolting on the head? How in the fuck???

 

Check this link... L series torque specs :)

http://www.davidcmur...20tech4.htm#TS2

 

 

Roll the engine over by hand after you get it torqued down and the chain set to make sure nothing is binding.

 

Yeah I did it with the head off... pretty easy.

 

All is well and it runs like a champ.