frodo70444 Posted September 23, 2010 Report Share Posted September 23, 2010 So I'm picking up this B310 on Sunday... I don't think i have ever seen a coupe(not hatch) 2 door B310 anywhere... looks straight. It has 148k miles on it and was under restoration, newer interior etc... plans for now are to get it reliable(needs a clutch) and drive it to get to know the car. A funny thought crossed my mind, to make it look like the Tomica R30 race car, as the rooflines are somewhat similar. lol Anyway, any ideas as to upgrades? I have some maxima/280zx struts with the cartridges and rotors but no brake calipers. I also have some very comfortable like new condition Talon seats(better than the eclipse ones,as they have adjustable lumbar support) that I had in my 260z back in the day... id like to have those seats if u getrid of them if ur in the u.s maybe we can talk Quote Link to comment
67 411 Posted September 23, 2010 Report Share Posted September 23, 2010 Great project can't wait to see more Quote Link to comment
Master-O-Turbonics Posted September 24, 2010 Author Report Share Posted September 24, 2010 The seats are gone..... :-/ Installed silverstar headlights today. BIG improvement! Not bad for a $40 upgrade. I ordered all the ignition tune up parts... NGK plugs, new wires, cap, rotor, points, oil filter, and some tail light bulbs(how many quarts of oil do I need? don't have my service manual yet...) All for $53! awesome! LOL Quote Link to comment
Spades Posted September 24, 2010 Report Share Posted September 24, 2010 Installed silverstar headlights today. BIG improvement! Not bad for a $40 upgrade. if those are from Sylvania, BE CAREFUL!!! We have had about 15 or so cars go through my shop with wasted headlight harnesses, relays, switches, ect. that were using those headlamps. I read that the Osram(owners of Slyvania name) ones from overseas in UK/Japan aren't an issue, but allot of Sylvania Silverstars we get here in the states are a higher wattage bulb than what comes on factory cars, especially older vehicles. The bulbs don't normally burn out, but the wiring normally melts, or it takes a relay out, or sometimes melts stuff and shorts to ground because the bulbs are demanding more amperage than the wiring can deliver. We see it often with Silverstars and ricer blue bulbs from china, ect. They are brighter, but demand more current than most stock headlight harnesses can deliver. The GE Nighthawks are a clean bright white light and should be the factory wattage, and some other brands out there will be cleaner, whiter light at the same wattage as a normal headlight bulb. Just use caution! P.S. sorry to thread jack! That thing looks sweet for a car from the 80s...I have never seen a 2 door of those ever... P.S.P.S. Oil capacity should be 3.4 quarts(filter change included). Transmission 4.9 pints, rear axle 1.9 pints. Spark plug gap of .041", base timing 5 degrees BTDC at 700-800 RPM with a counter clockwise rotation....that is unless my shop manual is wrong :D Quote Link to comment
Guest DatsuNoob Posted September 24, 2010 Report Share Posted September 24, 2010 cool projext if i were you i would be ripping them bumpers off cause there heavy bitches From what I remember the seats are heavier than the bumpers :lol: Cool project. Quote Link to comment
sinner720st Posted September 24, 2010 Report Share Posted September 24, 2010 i personally think that datsun/ all cars in general from the 80's have big ugly govt. mandated bumpers that need to go to schnitzer to give japan some of their "old" steel back Quote Link to comment
Master-O-Turbonics Posted September 25, 2010 Author Report Share Posted September 25, 2010 Ahh soo busy this week! Looks like I'll be working some for the Corvette team this week at the Petit Le Mans. Testing is early in tomorrow morning. Quote Link to comment
Master-O-Turbonics Posted October 4, 2010 Author Report Share Posted October 4, 2010 Pulled the tail light out and thought that hole looked familiar... Its a really close fit, just going to need a little bit of trimming and then make a trim panel. 240z tail light of which I have a pair. Quote Link to comment
Master-O-Turbonics Posted October 13, 2010 Author Report Share Posted October 13, 2010 Quote Link to comment
metalmonkey47 Posted October 13, 2010 Report Share Posted October 13, 2010 You're kidding! The 240Z tails just slipped right in? Quote Link to comment
Master-O-Turbonics Posted October 14, 2010 Author Report Share Posted October 14, 2010 You're kidding! The 240Z tails just slipped right in? ALMOST. Had to trim about 3/8" of metal between the top and bottom, but its sooo frickin close I had to pull out the tin snips... Plus the original tail lights that were in it were full of water. Then drilled holes where the 240z bolt holes are in the plastic housing... waaa la original 3 bulb B210 harness(note the bulb fittings that were sitting under water and are rusted solid) 4 bulb 260z/280z harness that I happened to have that was in better shape than the 240z harness(either one would work) I removed the connector from the B210 harness, pulled all the pins out, un-crimped the B210 wires on the tail light harness, Crimped in and soldered the 260z/280z harness into the B210 pins, then reinserted the pins into the B210 connector. I'll have a finished picture tomorrow...No cutting at all required on the factory body harness... I wouldn't use any super high load bulbs as this is already pulling an extra bulb through the same wires that power 3 bulbs. Common parts-store LED bulb replacements are being used for some of my tail lights. Quote Link to comment
Master-O-Turbonics Posted October 14, 2010 Author Report Share Posted October 14, 2010 I keep laughing every time I look in my service manual. 1 Quote Link to comment
metalmonkey47 Posted October 14, 2010 Report Share Posted October 14, 2010 Are the old lenses any good? Like, heat cracked or anything? Mine are starting to look worse the more I clean up my car Been trying to find some Quote Link to comment
I'm BLUE Posted October 14, 2010 Report Share Posted October 14, 2010 Cool deal on tailights from 240z !!! Thought about blacking out the panel around the same area on the 210 ? ;) ( like the 240z has those black panels ) Quote Link to comment
Pumpkn210 Posted October 14, 2010 Report Share Posted October 14, 2010 Lets see it with the rings! Quote Link to comment
Mini-L320 Posted October 14, 2010 Report Share Posted October 14, 2010 Damn, the body looks pretty damn straight from seeing the pics. Quote Link to comment
Mini-L320 Posted October 14, 2010 Report Share Posted October 14, 2010 Nice 2-dr Sedan there! They have decent brakes, bigger than the B210 ones. use the time and money on wheels, or an engine swap. The 81 only has 65 HP max. L20B is a factory bolt in if you find the right parst. Is the L18 also a Factory Fit into a 210? Cause I have an L18 with a Suck Threw Turbo Setup that i wanna use. Quote Link to comment
Pumpkn210 Posted October 14, 2010 Report Share Posted October 14, 2010 Is the L18 also a Factory Fit into a 210? Cause I have an L18 with a Suck Threw Turbo Setup that i wanna use. Into a 210, yes. Pretty sure you can do it in a B210 with those moter mounts. My buddy gots a 78 510 with a stock L20B, I gotta do some final measurements, but me thinks those are the ones! Quote Link to comment
Mini-L320 Posted October 14, 2010 Report Share Posted October 14, 2010 Into a 210, yes. Pretty sure you can do it in a B210 with those moter mounts. My buddy gots a 78 510 with a stock L20B, I gotta do some final measurements, but me thinks those are the ones! Well Looks like a have my Winter Project Set and ready to go now. Tranny from a 280zx and 280z 5 Speeds fit on L18 right? I got 3rd and 4th gear Syncros Busted out. Quote Link to comment
Master-O-Turbonics Posted October 14, 2010 Author Report Share Posted October 14, 2010 Are the old lenses any good? Like, heat cracked or anything? Mine are starting to look worse the more I clean up my car Been trying to find some They aren't in bad shape! Just leaky around the inside edge. Quote Link to comment
Master-O-Turbonics Posted October 14, 2010 Author Report Share Posted October 14, 2010 Cool deal on tailights from 240z !!! Thought about blacking out the panel around the same area on the 210 ? ;) ( like the 240z has those black panels ) I'm trying to find some rear trim panels off a 240z but not much luck..... and I don't want to pay $50 for a set off ebay. I paid $50 for these lights and they are in average shape at best. Quote Link to comment
metalmonkey47 Posted October 14, 2010 Report Share Posted October 14, 2010 They aren't in bad shape! Just leaky around the inside edge. You lookin to get rid of them? Quote Link to comment
Master-O-Turbonics Posted October 15, 2010 Author Report Share Posted October 15, 2010 You lookin to get rid of them? ya sure man... I don't have any use for them. Quote Link to comment
Master-O-Turbonics Posted October 15, 2010 Author Report Share Posted October 15, 2010 Looks like I'll be picking up a COMPLETE with EVERYTHING Z20E this weekend to start my crazy engine build... we'll see how that goes. Quote Link to comment
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.