iflyfisher Posted September 3 Report Share Posted September 3 I recently put a set of the original 14" chrome steel wheels on my 720. Anyone have a picture of the center caps that fit these wheels? I'd like to find a set, but not quite sure what I'm looking for. Thanks Quote Link to comment
Thomas Perkins Posted September 4 Report Share Posted September 4 16 dollars each. Quote Link to comment
iflyfisher Posted September 4 Author Report Share Posted September 4 Thanks @Thomas Perkins. I presume those mount from the inside with the cap thru the wheel. Where did you find those? Ken Quote Link to comment
alfa7kar Posted September 4 Report Share Posted September 4 Gorilla Automotive HC227 Hub Cover, 4.25" I.D., Closed-End, Derby, Chrome - JEGS Quote Link to comment
Thomas Perkins Posted September 4 Report Share Posted September 4 16 hours ago, alfa7kar said: Gorilla Automotive HC227 Hub Cover, 4.25" I.D., Closed-End, Derby, Chrome - JEGS They are push thru. Quote Link to comment
Thomas Perkins Posted September 4 Report Share Posted September 4 This is what is on my 85 4x4.Deep enough for the 4x4.They push in. Quote Link to comment
Thomas Perkins Posted September 4 Report Share Posted September 4 (edited) Here is mine.American Racing Rims.I got 5 of them. Edited September 4 by Thomas Perkins Quote Link to comment
iflyfisher Posted September 5 Author Report Share Posted September 5 (edited) Thanks for all the comments Gents. Unfortunately, none of the referenced caps will work with these wheels unless I bore out the center a bit more. These wheels are about 3 15/16" ID. They also are not perfectly round. I scrolled through all the options on JEGS and didn't see any of this size. I have seen some plastic caps that snap over the center and clip onto the lug nuts, but not a fan of those. I'm not sure what the original center caps looked like for these wheels. Maybe they never had any. Edited September 5 by iflyfisher Quote Link to comment
Crashtd420 Posted September 5 Report Share Posted September 5 2 hours ago, iflyfisher said: Thanks for all the comments Gents. Unfortunately, none of the referenced caps will work with these wheels unless I bore out the center a bit more. These wheels are about 3 15/16" ID. They also are not perfectly round. I scrolled through all the options on JEGS and didn't see any of this size. I have seen some plastic caps that snap over the center and clip onto the lug nuts, but not a fan of those. I'm not sure what the original center caps looked like for these wheels. Maybe they never had any. Do you know anyone who 3d prints? I think I have seen that done by atleast 1 person here...... Quote Link to comment
iceman510 Posted September 5 Report Share Posted September 5 (edited) 3 hours ago, iflyfisher said: These wheels are about 3 15/16" ID. They also are not perfectly round. I believe those wheels are not perfectly round because the bump out locations are used for the centering (hub centric). You would not want to use the push-through type center caps on those. My hardbody had steel wheels with a similar center design like those and I think there were plastic center caps that snapped in with tabs. I know I got rid of the wheels years ago, but I'll look around and see if I have the caps. Otherwise check for Hardbody stock center caps perhaps. https://www.ebay.com/itm/304843569560?chn=ps&norover=1&mkevt=1&mkrid=711-117182-37290-0&mkcid=2&mkscid=101&itemid=304843569560&targetid=2315428265460&device=c&mktype=pla&googleloc=9013165&poi=&campaignid=21399030172&mkgroupid=173029507348&rlsatarget=pla-2315428265460&abcId=9447175&merchantid=433607992&gad_source=1&gclid=CjwKCAjwreW2BhBhEiwAavLwfEPr9T5DanvHmMNhL2Krpo1FbpOpEXigjSBcBCTHCtwNS3SxK_qtVhoCChkQAvD_BwE Edited September 5 by iceman510 Quote Link to comment
iceman510 Posted September 5 Report Share Posted September 5 I would add the the trucks over the years (mainly 720) have two different size center bosses on the hubs. I think the Hardbody uses the larger of the two. Quote Link to comment
iflyfisher Posted September 5 Author Report Share Posted September 5 (edited) @Crashtd420, Don't know anyone with a 3D printer. Thx @iceman510, I agree, I would think these wheels would use a snap in type of cap. There is room at the front hub for this type of cap to snap in. However, the rear wheel sits tight to hub all around the edge of that center bore. There would be no room for a cap to snap in unless I used some sort of spacer to pull the wheel a bit away from the hub. I do like this wheels. They definitely have the period vibe. But they would look better with some type of cap. I'll keep looking. Edited September 5 by iflyfisher Quote Link to comment
iceman510 Posted September 6 Report Share Posted September 6 Submitted for your viewing pleasure. 2 Quote Link to comment
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.