five10 Posted July 13, 2021 Report Share Posted July 13, 2021 Gents, I need some expert advise. I have no power to the starter and it's brand new. (the last one lost its return spring tension and it got chewed up by thr flywheel, it also did not have power). I am aware that there is no relay from the ignition to the starter. From what I can see it looks like the starter is wired directly to the ignition. My ignition is also new. 72 510 4 door, L18, 5 speed and what looks like an automatic engine bay harness that I bought for 30 bucks. I have extra wires that go to the neutral safety switch which are currently not being used. The 2 problems/solutions I can think of is: 1). Attach a neutral safety switch (because of automatic harness) 2). Drop of voltage to starter, buy hotwire relay kit. A part of me wants to replace the entire harness for an updated one from painless (I have done this to my 69 Cobra) but it's extremely time consuming. Your thoughts and/or advice is deeply appreciated. Quote Link to comment
five10 Posted July 13, 2021 Author Report Share Posted July 13, 2021 I believe this goes to the neutral safety switch on an automatic transmission Quote Link to comment
five10 Posted July 13, 2021 Author Report Share Posted July 13, 2021 I have no clue what these go to Quote Link to comment
five10 Posted July 13, 2021 Author Report Share Posted July 13, 2021 These were left out under the dash. Quote Link to comment
five10 Posted July 13, 2021 Author Report Share Posted July 13, 2021 Coil. This was in the car already and it is missing a wire from somewhere. There is a second coil that came with the car but the plugs don't match up. Quote Link to comment
five10 Posted July 13, 2021 Author Report Share Posted July 13, 2021 Here is the second coil Quote Link to comment
datzenmike Posted July 13, 2021 Report Share Posted July 13, 2021 43 minutes ago, five10 said: Gents, I need some expert advise. I have no power to the starter and it's brand new. What you mean is you have no start signal to the starter from the ignition switch? 26 minutes ago, five10 said: I believe this goes to the neutral safety switch on an automatic transmission The start signal from the ignition switch travels down the Black/Yellow wire to the automatic interlock switch and out the other Yellow/Black wire to the starter. Just cut the two Yellow/Black wires and crimp them together and the start signal will now pass to the starter. The other pair of wires are for your back up lights. They should connect to the reverse switch on your 4 speed transmission. 24 minutes ago, five10 said: Here is the second coil This looks like the stock 510 coil and ballast resister. The green lettering probably says must use an external ballast resister or something like that. 27 minutes ago, five10 said: Coil. This was in the car already and it is missing a wire from somewhere. There is a second coil that came with the car but the plugs don't match up. This one looks similar. Can you post a picture of your distributor? with the cap off?? Quote Link to comment
banzai510(hainz) Posted July 13, 2021 Report Share Posted July 13, 2021 (edited) the coil wireing of hand looks good the no start 12volt to the Starter goes thru the trans wires when in PARK its shorted out .On AUTO trans wire harness. soem post the 510 wire driagram for this its simple wiring. Edited July 13, 2021 by banzai510(hainz) 1 Quote Link to comment
five10 Posted July 13, 2021 Author Report Share Posted July 13, 2021 Thank you both. Mike, here is a dizzy Pic you asked for. Quote Link to comment
datzenmike Posted July 13, 2021 Report Share Posted July 13, 2021 OK I thought maybe an electronic ignition but not.''What does the green lettering say? Quote Link to comment
five10 Posted July 13, 2021 Author Report Share Posted July 13, 2021 Spliced the b/y wires together, still no signal. I'm going to follow the diagram banzai posted and ensure all wires are where they are supposed to be. Quote Link to comment
five10 Posted July 13, 2021 Author Report Share Posted July 13, 2021 (edited) It says "ballast resistance required" Edited July 13, 2021 by five10 Quote Link to comment
datzenmike Posted July 13, 2021 Report Share Posted July 13, 2021 22448-H7207 ? is for a '73-'77 620 truck, which is fine it will work on a 10 just fine. Do you have a cheap $4 test lamp. It's invaluable tracing 12v along wires? Quote Link to comment
five10 Posted July 14, 2021 Author Report Share Posted July 14, 2021 I do have a test lamp. Let me find it Quote Link to comment
banzai510(hainz) Posted July 14, 2021 Report Share Posted July 14, 2021 I forgot to mention if a auto wire harness was installed ,, Does that mean the wires all the way down to the trans got replaced? or just the engine harness. other wise one needs to know where to make the Jumpers. or if car was a AUTO already then one just makes a jumper(a short) then plug into the orginal harness Quote Link to comment
five10 Posted July 14, 2021 Author Report Share Posted July 14, 2021 I just have the engine harness. Quote Link to comment
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.