Mehly20 Posted October 28, 2012 Report Share Posted October 28, 2012 I just purchased an 81 720 King Cab with a 5 speed manual. It was slipping out of 5th gear initially. I read a few things and checked the bolt holding the ball an spring on the passenger side behind the middle plate. I loosened it and re tightened the bolt. I went and checked it and it wouldn't even go into 5th or reverse. I took the bolt completely out and tried to draw the ball and spring out with a magnet but my magnet was to large of a diameter. I replaced the bolt and have the same problem. I am new to Datsuns and motors/trannys in general. I am learning a I go. Any ideas? What other transmission can be a straight bolt up with this year an model? Thanks!!! Quote Link to comment
Dat Lurka Posted October 29, 2012 Report Share Posted October 29, 2012 I believe any trans for L or Z series engines will fit. Sounds like yours is fixable though, considering you broke it :poke: Please, honor us with pics. Quote Link to comment
Mehly20 Posted October 29, 2012 Author Report Share Posted October 29, 2012 I will snap a few pictures when I get home. Is there a possibility something is out of line or the forks that hold it in gear are shot? Like I said, I'm far from knowledgable with this stuff and any help is greatly appreciated as I learn this truck as I go. Quote Link to comment
Dat Lurka Posted October 29, 2012 Report Share Posted October 29, 2012 Could be bent shift fork. Quote Link to comment
ggzilla Posted October 29, 2012 Report Share Posted October 29, 2012 The good thing is you can drive in 4th. In fact, you can go faster in 4th gear. 5th just saves gas. Quote Link to comment
Dat Lurka Posted October 29, 2012 Report Share Posted October 29, 2012 ^ He may want to get his reverse working 1 Quote Link to comment
datzenmike Posted October 29, 2012 Report Share Posted October 29, 2012 This?... It merely centers the gear lever when you let go of it in the neutral gate. Has nothing to do with the gears. Loss of 5th is more likely to be the nut on the mainshaft backing off. Slowly the 5th gear is forced back towards the rear. Eventually just the pressure on the gears from driving will pop it out of gear. Eventually it won't even go into gear. The large nut on the mainshaft to the right. . Quote Link to comment
Mehly20 Posted October 29, 2012 Author Report Share Posted October 29, 2012 I have a picture taken but can figure out how to add it in my reply from my phone. Sorry, I am new to this forum. Quote Link to comment
ggzilla Posted October 29, 2012 Report Share Posted October 29, 2012 From your phone, post the picture to Photobucket or other photo app. Then in your reply link to the photo site. Quote Link to comment
Mehly20 Posted October 29, 2012 Author Report Share Posted October 29, 2012 Here is the picture. It is the bottom bolt I loosened and re tightened which caused it to lock me out of 5th and reverse. I then completely removed it and fluid ran out the hole. I put my magnet, which was too big for the hole, and nothing came out. I put it back in and still had the same problem. http://m1281.photobucket.com/albumview/albums/mehly20/Mobile%20Uploads/IMG_3347_zpsa4387bc4.jpg.html Quote Link to comment
ggzilla Posted October 29, 2012 Report Share Posted October 29, 2012 Man that is a small photo. Photobucket will let you upload the full size camera image. Quote Link to comment
Mehly20 Posted October 29, 2012 Author Report Share Posted October 29, 2012 It's straight off my iPhone 5. Its best I can do until about 8 hours from now. Quote Link to comment
datzenmike Posted October 29, 2012 Report Share Posted October 29, 2012 At the least it will need to come out. Quote Link to comment
datzenmike Posted October 29, 2012 Report Share Posted October 29, 2012 Here is the picture. It is the bottom bolt I loosened and re tightened which caused it to lock me out of 5th and reverse. I then completely removed it and fluid ran out the hole. I put my magnet, which was too big for the hole, and nothing came out. I put it back in and still had the same problem. http://m1281.photobu...387bc4.jpg.html Oh.. that one. It helps hold in gear. It's called a detent ball and it rolls as the shift rod is moved forward and back. On the shift rod at the rev. and 5th position there is a small notch in the rod that the ball drops down into, pushed and held there by a stiff spring. You may have noticed a light click sound as you go into gear... this is what causes it. You should still be able to place it in gear though. Quote Link to comment
wayno Posted October 29, 2012 Report Share Posted October 29, 2012 Man that is a small photo. Photobucket will let you upload the full size camera image. I just grabbed and posted what he had ggzilla, I am sure given enough time I could have enlarged it, but it is very difficult for me to do, as I really don't understand computers, so I just grabbed what was there and posted it. Quote Link to comment
ggzilla Posted October 29, 2012 Report Share Posted October 29, 2012 You cannot enlarge a digital photo. They come out of the camera much bigger than that, even with the cheapest, oldest digital camera. Quote Link to comment
Mehly20 Posted October 31, 2012 Author Report Share Posted October 31, 2012 I tried posting this as a new topic but they locked it up. This is a completely different issue but they are making me post here.. When driving, and it gets worse the higher the RPMs, and I disengage the clutch by pressing in the clutch pedal I get a rattling and somewhat of a grinding noise. If I shift into neutral it stops but if I stay in gear or downshift and keep the clutch in it gets bad. I don't think it is related to the topic above but any ideas? Throw out bearing possibly? Thanks!!!! Quote Link to comment
wayno Posted October 31, 2012 Report Share Posted October 31, 2012 I tried posting this as a new topic but they locked it up. This is a completely different issue but they are making me post here.. When driving, and it gets worse the higher the RPMs, and I disengage the clutch by pressing in the clutch pedal I get a rattling and somewhat of a grinding noise. If I shift into neutral it stops but if I stay in gear or downshift and keep the clutch in it gets bad. I don't think it is related to the topic above but any ideas? Throw out bearing possibly? Thanks!!!! Your saying that if the clutch pedal is pushed in, and you shift into neutral the noise goes away, does it make noise while in neutral with the clutch out when not moving? Quote Link to comment
Mehly20 Posted October 31, 2012 Author Report Share Posted October 31, 2012 No it's fine at all times while in neutral. It only rattles as grinds when I have the clutch in and in gear. Quote Link to comment
ggzilla Posted October 31, 2012 Report Share Posted October 31, 2012 Transmission input shaft bearing. That photo is 1/20th of a Megapixel. The iPhone 5 takes larger pics than that, so you might have the iPhone camera app on the wrong setting. Photobucket "uploads" settings do not have an option for that exact size. Quote Link to comment
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.