80datson Posted October 1, 2011 Report Share Posted October 1, 2011 Does the 1980 200sx come with the 4 link with h165? Quote Link to comment
datzenmike Posted October 1, 2011 Report Share Posted October 1, 2011 Yes. The '80 had a 4 link, H-165-B axle with rear disc brakes and 3.7 ratio differential for standards and automatics. Quote Link to comment
80datson Posted October 1, 2011 Author Report Share Posted October 1, 2011 Should me a direct bolt onto my 1980 210 right? Quote Link to comment
datzenmike Posted October 1, 2011 Report Share Posted October 1, 2011 Famous last words. lol The 210 has an H-150-A rear axle and is 2 inches shorter (wheel tread) than the 200sx but the width could be the rim offset. An H-165-B is not the same as an H-150-A. Although they may have 4 link and coil springs and the e brake pulling across the back the 210 uses pressed in U joints that are likely smaller than the 200sx and probably the drive shaft won't bolt to the 200sx diff flange. There may be subtle differences in link length, coil mounts, shock mounts. Measure carefully. Quote Link to comment
80datson Posted October 2, 2011 Author Report Share Posted October 2, 2011 http://i122.photobucket.com/albums/o255/88cRex/IMG_20111001_182005.jpg Quote Link to comment
datzenmike Posted October 2, 2011 Report Share Posted October 2, 2011 From '80-'81 S110, very nice. It may fit, you never know. Quote Link to comment
80datson Posted October 2, 2011 Author Report Share Posted October 2, 2011 That you good sir.. turns out its a perfect fit. Wouldn't have known if it wasn't for "leosnake"... now I have a h165+rear disk brakes+rear sway bar sweet!!! Out with the small in with the big ;) Quote Link to comment
Master-O-Turbonics Posted October 2, 2011 Report Share Posted October 2, 2011 a later 200sx H190 will also fit and with stock datsun wheels, might have to roll fenders if you want super low like this pic of my B310 w/ 200sx H190(no springs for the pic): one more thing... this would never happen if there was a 3rd member installed unless the trans tunnel was cut out. Quote Link to comment
80datson Posted October 2, 2011 Author Report Share Posted October 2, 2011 nice. but if i decide to go past that 225 torq mark then i will start looking. hell, its hard enough to even find a h165 at the junk yard i got lucky yesterday and also it was 50% off so i got that whole set up for under 150. Quote Link to comment
datzenmike Posted October 2, 2011 Report Share Posted October 2, 2011 fap,fap,fap,fap,fap,fap,fap,... ugh! Quote Link to comment
80datson Posted October 2, 2011 Author Report Share Posted October 2, 2011 fap,fap,fap,fap,fap,fap,fap,... ugh! :P what is this language you speak of Quote Link to comment
datzenmike Posted October 2, 2011 Report Share Posted October 2, 2011 fap, fap, fap Quote Link to comment
Master-O-Turbonics Posted October 2, 2011 Report Share Posted October 2, 2011 ROFL Quote Link to comment
80datson Posted October 2, 2011 Author Report Share Posted October 2, 2011 lmao!.... fap fap fap.. "Fap The sound made when you jack off. *Fap fap fap fap fap* Fred: Hey, whats going on in there." Quote Link to comment
datzenmike Posted October 2, 2011 Report Share Posted October 2, 2011 Thanks for the rear end porn. Quote Link to comment
80datson Posted October 2, 2011 Author Report Share Posted October 2, 2011 no problem want more pics to fap to? Quote Link to comment
80datson Posted October 2, 2011 Author Report Share Posted October 2, 2011 also cant wait to get everything tied up so i can get my car running then ill show you a smokey burn out since BURLEIGH wasnt abke too cause his h150 didnt take well to hard fap'n Quote Link to comment
vex210 Posted October 2, 2011 Report Share Posted October 2, 2011 Nice score again!!! you and Burleigh are did it right... :thumbup: Quote Link to comment
80datson Posted October 2, 2011 Author Report Share Posted October 2, 2011 thanks dude! yeah one day i want to have a race on the strip with Burleigh and settile which is the best. round nose or square nose! :P Quote Link to comment
vex210 Posted October 2, 2011 Report Share Posted October 2, 2011 I would love to see that race.... :rofl: Quote Link to comment
Master-O-Turbonics Posted October 4, 2011 Report Share Posted October 4, 2011 thanks dude! yeah one day i want to have a race on the strip with Burleigh and settile which is the best. round nose or square nose! :P IF you were running an H190 I'd loan you my welded 4.88 alloy 3rd member to WIN! haha! Quote Link to comment
80datson Posted October 4, 2011 Author Report Share Posted October 4, 2011 IF you were running an H190 I'd loan you my welded 4.88 alloy 3rd member to WIN! haha! LOL where did you get that h190 BTW? Quote Link to comment
Master-O-Turbonics Posted October 4, 2011 Report Share Posted October 4, 2011 LOL where did you get that h190 BTW? Pullapart! I have one bare housing that I got from a guy then a complete one from an 82 S110 . I usually get 3rd members from roadster guys or rally 210 guys Quote Link to comment
BURLEIGH Posted December 28, 2011 Report Share Posted December 28, 2011 thanks dude! yeah one day i want to have a race on the strip with Burleigh and settile which is the best. round nose or square nose! :P Haha! Just saw this one... Square is faster, but round gets the "chikas"...! Nice build by the way! Quote Link to comment
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.