leeroy jenkins Posted June 6, 2013 Report Share Posted June 6, 2013 All exterior lighting works but the headlights high and low do not. The filaments in the lamps are not blown. Does this sound like a ground issue? Quote Link to comment
laotsu Posted June 6, 2013 Report Share Posted June 6, 2013 sounds like a fuse issue. try removing the fuse block and soaking it in vinegar. just be sure to take a pic of everything before you disassemble it. Quote Link to comment
datsunaholic Posted June 6, 2013 Report Share Posted June 6, 2013 Sounds more like a relay issue, but grounds could do it. Also could be a blown fusible link feeding the headlight relay. Quote Link to comment
rus Posted June 6, 2013 Report Share Posted June 6, 2013 Sounds more like a relay issue, but grounds could do it. Also could be a blown fusible link feeding the headlight relay. Last time I checked 280z did not have headlight relays. Quote Link to comment
leeroy jenkins Posted June 6, 2013 Author Report Share Posted June 6, 2013 Forgot to add that it is a 1976 280z. Quote Link to comment
rus Posted June 6, 2013 Report Share Posted June 6, 2013 Check fuses and fusible links. 280z didn't come with headlight relays, power goes directly from battery through combination switch. Check grounds and power wires at the steering column Quote Link to comment
darrel Posted June 6, 2013 Report Share Posted June 6, 2013 And work the switch on and off a number of times. Sometimes corrosion sets in and fouls the contacts. Quote Link to comment
Mannyvig Posted June 6, 2013 Report Share Posted June 6, 2013 It's the combo switch. Not having a relay means that way too much amperage runs through the crappy contacts in the switch. If you pull the column cover off you may be able to see burn spots on the switch itself. Very common issue for the Z. Quote Link to comment
leeroy jenkins Posted June 9, 2013 Author Report Share Posted June 9, 2013 Tried most everything suggested. No use. The switches at the column appeared clean. I used contact cleaner on the entire area including the plugs. Un-plugged and re-plugged all. Eventually I tried an older switch I had previously replaced. Used the cleaner to blast the fuse box face and back side. I also stole a trick from a different site user who suggested grounding the red/ black wire from the low beam. All a failure. I am going to button the whole thing up tomorrow and take it to a pro. Thanks for the responses. New to the membership. I have come to the site for a few years now. All good stuff. I will try to contribute when I can. Done a lot of work on mine. Z's are a true sports car. A pain like a good family member...tolerable. Quote Link to comment
leeroy jenkins Posted June 10, 2013 Author Report Share Posted June 10, 2013 Fixed it. It was the "Fusible link". That would seem obvious. It was not so evident. We worked to replace bulbs blown in the gauges. Cleaned up some wiring underneath. Before packing it in for the day, I moved to the fusible link location and I began to tug ever so slightly on the wires. The "headlight switch" wire broke free with little effort. I re-attached the wire with a new connector. Both headlamp low and high beams were now functional. Just as information, I researched and found a Site in regard to fusible links-- http://www.atlanticz.ca/zclub/techtips/fusible links/index.html My case was in regard to a 1976 280Z. The information will cover: 75,76,77 and an upgrade. Standing in front of the car looking into the engine bay, look to the left and to the rear of the strut tower. There will be two small boxes with four "link" connections. My links are open/ no covers. Some will have plastic covers. From the grille position looking forward, the left near connection link is for the alternator and ignition relay. The left far link is for the headlight switch. The right near link is for the ignition switch and the right far link is for the ignition and electronic fuel injection relay. I had re-connected the headlight switch link in the past. Obviously, my repair was not sufficient. I am going to purchase new link connector wires for all. I hope this will help a few of you. Quote Link to comment
darrel Posted June 10, 2013 Report Share Posted June 10, 2013 Dave Irwin can make a headlight harness and a parking light harness for the 280z. The parking light harness should be a 9 pin connector on your '76, same as in the 240 and 260z with the intermittent wipers. For the headlight harness, you would need a sacrificial 280z harness, using both harness connectors for the headlights and one pigtail for one of the headlights. Quote Link to comment
KFD Posted June 12, 2013 Report Share Posted June 12, 2013 It's a simple fix. You need to ground the red/black wire running to the connector directly behind the charcoal canister at the front of the engine compartment on the passenger's side... KFD Quote Link to comment
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.