Tuan Posted July 14, 2012 Report Share Posted July 14, 2012 Hey everyone, ASKING $3800 OBO OR TRADES Early 1974 Datsun 260z :+: Car’s info :+: 10/10 *Clean California Title *Title in hand, I am the 3rd owner. *Tags, registration, insured and “Zero” fees owed. * 1974 so it’s smog exempt “woot” :+: Engine/Trans :+: 8/10 *Original Inline 6- L26 (2.6 Liter) OHC Produces about 140-160hp. *I did a compression test on it, and all 6 cylinders produced at least 180psi *Clifford aluminum 6=8 manifold *Holley 390cfm 4 barrel carburetor *Holley tuned with .25 discharge nozzle and blue pump cam *Header *ZX Electronic Distributor upgrade *MSD ignition coil *Custom Strut bar *Custom fuel hard lines *Custom Wire tuck *New Kyosan mechanical fuel pump *New Duralast thermostat-water pump-belts- life time warranty *New freezeplugs *Castrol GTX high mileage 10w-40 ** Original 4 speed manual 9/10 *Pennzoil 80/90 + Pennzoil Syncromesh (For transmission) *Pennzoil 80/90 in stock open differential 3.54 :+:Cooling:+: 9/10 *3 row aluminum radiator *2 (10”) Electric fans *Adjustable thermostatic switch (Kragen) Lifetime (Temp set at 174 degrees) *New Dayco upper and Lower radiator hoses *New Polished 2X13” aluminum upright coolant reservoir :+:Braking / suspension/wheels:+: 10/10 ! *Z32 (300zx) Dual Diaphram ABS brake booster upgrade *S13 Brake master cylinder upgrade *New brake hardlines *Modern Motorsports 240sx rear disc conversion upgrade: *MM Brackets, Z31 rotors, + 240sx rear calipers with Duralast Gold pads *Front Calipers were rebuilt and they have P.B.R. soft Aussie pads. *Front rotors are Brembo blanks. *Sitting on Eiback Lowering Springs + 4 New Monroe shocks *New all sway bar end-link bushings *15” ZX swastika wheels + newer rear tires :+: Interior / Exterior:+: 6/10 *Custom Dash (Aluminum formed) *Custom Center Consol (Aluminum formed) *JDM HUB *Cheapo 330mm steering wheel *Custom shifter **2008 Mazda Miata MX5 seats! Brand new *with the seat belt unit retrofitted **Chrome Roll bar **Rear Custom Strut bar **Thin MDF wood grain panels / trim panels **Stock gauges (all function) **Acc/On/ Start switches **LED bulb upgrade *JDM/Euro amber tail lights *New Winshield + rubber *New Kia sportage door weather seals *New Fox body mustang rear hatch seal *Xeson front dam/lip *Custom front grill *Bosch 7” Motorcycle E-code H4 housings *Generic H4 HID 6000k kit. *Magnaflow XL muffer *240z rear bumper with 240z front bumperettes. *Vented Z hood with grills Please give me a call or text to test drive her. (818) 748-7111 I am testing the waters and I have an early 1974 Datsun 260z for sale. I will consider cash offers as well as trades. Description/Summary: I am looking to sell or trade this cool Datun 260z as I am a bit bored of it. I’ve spent countless hours upon hours working on her and it was quite fun as well as a very enlightening experience. Now that it’s almost coming to an end, I need a new project. As I’ve always wanted to own a Z, I’ve done so and now I”ve gained a lot of knowledge and realization how much money and time it takes to own and maintain/restore one. I am looking to sell this car or trade it for a nice daily driver that either has 4 doors or large or just gets good mileage and practical for daily commute. With regards to the engine and drivetrain, it’s 10/10. She starts up every time, may it be cold or hot, no choke needed because of the dependable Holley carb set up. With regards to interior and exterior, she needs a little bit of work, but most of which I’ve done. There floor pan is rusty and I’ve cleaned up as much as I could and Por15 treated it as well as Herculine truck bed lined it. She needs a little finesse and body work, and interior work. Floor pans should be fixed but can and will survive for a while. 1 Link to comment
Skib Posted July 14, 2012 Report Share Posted July 14, 2012 should bring it down to the eagle rock swap meet this weekend in glendale. gonna be a toooon of people there Link to comment
AkiZ Posted August 1, 2012 Report Share Posted August 1, 2012 Willing to ship at all? Link to comment
SlimerZ Posted August 16, 2012 Report Share Posted August 16, 2012 Is this still for sale Link to comment
nismosilvia Posted August 18, 2012 Report Share Posted August 18, 2012 Do you have a parts number for the clifford intake that you could pm me? Gluck with the sale Link to comment
Tuan Posted August 22, 2012 Author Report Share Posted August 22, 2012 The car was sold today. And sorry i didnt get a chance to get the part number but i think thwy still make them and still for sale. Google clifford manifold and you should find it. Link to comment
Recommended Posts