Thomas Perkins

Could be your linkage is sticking.Happened to me.If you can,when it gets stuck idling high,just push the throttle with your hand and see if it idles down to your set point.If it does then your linkage is sticking,your nut there is too tight.Bend the washer that secure that nut and loosen nut a cunt hair and bend washer tab back.Here is the part that holds the nut secure.Also spray some WD-40 there.Never ever had a problem with my choke on my Weber.Change your gaskets yearly.Cheap and easy to do.Also spray some WD-40 on your high idle speed linkage.

First check your blower motor resistor.

On my experience with stock carbs and Webers on my 85 4x4.I get around the same.18 to 19 mpg average.I go no faster than 70 cause out here they have speed checks everywhere.

I use a 60 amp.50 is not enough for mine.I have a A.C.Next time you need one get a 60 amp one,same price.I noticed a lot of my electrical stuff was not working like it should with a 50 amp one.

Rock Auto parts are a great place to get great parts at great prices.

Glad it worked,also stay away from Auto Zone's belts.How many amps is your alternator?

My Head lights quit working once and it was the fusible link.I think it was the  red one.It melted the  plastic on the yellow connector that is use to connect  both wires.All I did was replace the yellow connector.All my wires that connect to the fusible link that has male connectors all dry rotted so I replaced them with these.

Auto Zone's are poor.They rust real bad  and don't last long but they are free after that.You can bleed a bad one and make it home.I did from work one day.

This is mine on my 85.I have a new spare.Not parting with it.

Gate belts are the best.

I screwed in the screw a little bit then went to drill other hole and hub moved,so it came off.Kewl.I can now take the hub to my table and finished drilling and tapping.

Got one done.

Other side is done.

10 minutes ago, Ooph! said:

Regular bits will work, go slow and use oil any type will work if you don't have cutting oil.

 

Yep I just drilled a pilot bit thru it fixing to do the other one.Went thru it easy.

The passenger side brake drum does not have the two threaded holes for the 8 mm bolt to screw in to push drum out.Has any one ever drilled cast iron and what drill bits to use and oil.

Ok

I got my new replacement wheel cylinder today.The guy that put the order in was trying to charge me freight.This one is good,pistons both work.I went to the Nissan dealer and picked up a couple of brake secondary brake clips,just 4 bucks,they had this Nissan Z In the the show room with a stick shift.52,700 bucks,I would get the Nismo.They had 2 GTR's in there a time ago.Check this out.For a extra key,you have to pay 595 bucks.It says,you put 36 grand down and your payments will be 304 a month for 72 months.

You can have it.Just pay shipping.I will clean it up and paint it.Give me your address,I will wrap it up and take to post office and find out the shipping charge.I am in Georgia.I will first take pictures and post it.It was on my truck.I thought I needed a new one but the resistor was bad.

I have a good Nissan one if you want it.Also a Nissan white blower motor resistor bought from Nissan long ago.Still in box, they make 2 kinds,a white and black one.

Get a Empi  idle cut off solenoid.

Wish you live here in Georgia.You could show me a thing or two.I amstill waiting for my other brake cylinder from O'Reilly's.Maybe it will be here today.I got my 2 clips that hold the emergency secondary brake.Just in I ever need some.A little over 4 bucks for them.Got themlocal.Free shipping.I am.putting a rack and pinion on my wife's 2004 Lincoln LS.I got the part from RovAuto Parts.'.I havea great shop manuals that tell you the part number.Way be than Nissan's.3 big books.

Don't have time to do major work.I feel better getting it done right.I've had about 3 blown head gaskets in 30 years and they have done it right.Even had a Jasper engine installed by a Jasper installer back in 2009.Jasper only sells to installers.I have 106,000 miles on it.Check out my 39 year old truck.I am doing something right.

I Pay and don't have the time to do it.