Jump to content

Headlight Ring Repair


Recommended Posts

  • Replies 10
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

Posted

Polished stainless I think.  They are also the most lost things on a 620, rarely are they complete. Looks like the right side (low beam) outer ring is the same as the left side inner or high beam. Right side high beam is the same as the left side low beam. What one is damaged on your 620?

Posted (edited)

Left side inner. They were bought from another 620. Looks like they mangled it trying to remove them.

Edited by GRJones
Posted

 

GRJones said:

Left side inner. They were bought from another 620. Looks like they mangled it trying to remove them.

Edited Tuesday at 03:12 AM by GRJones

 

Those rings bend surprisingly easy once somebody pries at one edge. The donor truck parts game always has one little surprise tucked in.

Posted

 

 

There are four tabs that poke through the grill and are bent over. The grill has to come out for any chance of removing them. The two I removed had all four tabs. I straightened them but two of the four would not push back through and they must have snapped off. Lost headlight trim rings is problematic for the '73-'77 grills, they just snap off and the ring is lost.

 

Definitely GLUE them to the grill if you want to keep them.

  • 2 weeks later...
Posted

Those rings look fairly fixable. 

 

You'll need a light hammer, and a heavy smooth 'anvil' to work on. I make my own shaping tools to fix stainless brightwork, each piece's profile is different. The closer you get your 'tool' to the actual shape you want, the easier the shaping will go. You'd most likely want to use a wedge-shaped tool first to open up those really bent ones. The 'really bad' creases might split if you work them too much. Stainless has this fun tendency to harden up when it gets bent out of shape...  If it does, it can be annealed, but you're getting into a big can of worms when it comes to that thin of material.

 

Once you get them as straight (or 'round', in your case) as you can, it's time to break out the sandpaper. GO LIGHT on the pressure!!! I start around 800 grit with dish soap and water on most trim, and take it out to 3 or 4k. If I was doing a show car, I'd go out to about 10k. There's no real visible difference after about a 4k grit finish, but the pieces will feel like more and more they're made of liquid metal to the touch as you go higher and higher...

 

I'll snap some pics of my process next time I start straightening some trim.  I just did the headlight rings on the 510, they came out pretty OK for some pieces of stainless that have been buried in rotting pine needles for <gulp> 25-ish years now...

 

 

Posted

Sorry to have you write that guide up but it's good for others. Datzenmike sent me an extra one he had. Very happy with them. 

 

20261004_114121(1).thumb.jpg.ff4a5554a363a3b1ff342c8b0af9f73d.jpg

Posted

Those earlier 620 front ends looked SO good!  Your truck is gonna be BEAUTIFUL when you're done with it. Already is, really.  Now I have to go look at the grille of my 78. 

 

And, no worries on doing a little write-up.  If it can inspire someone to get going on their car or truck, awesome.

 

 

Posted

One of the first things I changed on my '78 was to put an earlier '73-'77 grill on it. Front away bars are an option supposedly. My '78 didn't have one so that was next. Holes in the frame are already there and threaded. 

Posted

You had me all excited there for a minute, Mike!  I ran down to my 620, ready to see the uber-rare Nismo sway bar setup on there.  But no.  Shucks.  

 

I found a few more things that needed to come home with me though.  lol. I need to stop looking at that truck.

 

 

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...
×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use.