Jump to content
volkswagner

Track Rat - 1991 Pulsar GTIR

Recommended Posts

While browsing the world wide classifieds for SR20 parts for my 510 wagon build, I happened across this ad.
Capture.png

My interest was peaked and I toyed with the idea for a while but eventually moved on.
After a couple months, I came to find out that the car never sold and was still sitting at Sodo-Moto. 
Both Carter and Jeff had dealt with Sodo moto and had nothing but positive reviews.
So, I decided to go down and take a look. The ad made it clear that the car was beat down with a lot of "janky tuner mods" and "battle scars"
When we got down there it was clear what they meant.
45420153-347921922431266-888164805348478

IMG-9673.jpg

45583944-347921895764602-155710972709830

45424011-347921969097928-988580503785308

 

"Track Rat" seemed to be a accurate description. The car looked like it had been raced quite a bit. Bolt in cage, a few performance upgrades, race seat, coil overs, and  a lot of electronics tied to the ECU. We took stock of the state of the car. As they advertised, the car had some damage on each quarter, it was filled and then re-damged on both sides. Seems the guy wasn't very good at his racing of choice.It did not run as it sat. Sodo Moto had only gone as far as ripping out a bunch of excess wiring shenanigans and diagnosing a fouled fuel pump. Other than that they knew it popped when fed some ether.  
I knew if I were to get the car it would need to be a runner without extensive work. The owner gave us permission to toy with the car at our will.
He brought out a cheapo pump and with the tools I brought we had it fired up in short time.
Surprisingly, even after what we guess to be at least 15 years, the SR roared to life. A smooth idle, good compression, boost pressure, some vapor, minimal smoke.
However, lots of lifter noise. Since the GTiR has a solid lifters, they are louder than the normal hydraulic lifter SR but this was excessive. This came with low oil pressure, only about 30psi and not much gain with rpm. 

Engine = good enough
Next was the transmission, these cars are notorious for blowing there cogs all over the ground when the overzealous try to put too much boost  through all four wheels.
Unfortunately, the tires were flat. (Actually worn in half on one by what I assume to be the cars last burn out session before being parked.)

So, put it in every gear and pulled forward and back. No grinding, no red flags, best that could be done. 
Transmission = good enough

Brakes, rusted in place and needing a complete overhaul.
All glass good.
No heavy rust/rot underneath.
Interior, seats all there and looking fresh. They even had the minty stock drivers seat! The dash was trashed by gauge mounting and sun cracks.
There really wasn't much more to be learned. 
A deal was struck and then it was just waiting for delivery. 

 

Since I still have my torn down wagon clogging up my only garage bay, Jeff was generous enough to loan me one until the car is a driver. Thanks buddy!

47149266-1868029729961087-63560901294154

Parked next to his coupe that he also got from Sodo, how fitting!


 



 

 

  • Like 7

Share this post


Link to post

Great to see a build thread on this interesting car Sam!

Share this post


Link to post

I heard you got one of these. Awesome AWD car. 

Share this post


Link to post

Saw one of those a couple of yeas ago in town. Had to look up what it was. Or was there another Nissan awd with the hood inter cooler??? There was a huge amount of import cars around here then. Saw a different GTR every week.

Share this post


Link to post

That's cool always wanted one of these or at least take a wrecked one and transform a F10 into one.  Sodo Moto same guys who have that toyota crown wagon right?

Share this post


Link to post

With the car in Jeff's shop it was time to go over it with a bit more vigilance and look for any surprises good or bad, that it may have in store.
Up on stands for inspection/work.

IMG_9729.jpg

 

Lots of tuner bits in the bay
IMG_9901.jpg

Crusty coilovers

IMG_9777.jpg
 

Dude was a shit driver turns out

IMG_9735.jpg

Those won't be flapping much mud!

IMG_9731.jpg

Stainless turbo back...

IMG_9727.jpg

Well, turbo back until the sweet tail pipe yo!

IMG_9713.jpg

 

Worlds shittiest dash installments

IMG_9752.jpg

IMG_9751.jpg

 

junk in the trunk

IMG_9743.jpg

Sticker galore

IMG_9741.jpg

 

A little switch on the dash, translated to up=KSROM down=normal
Since it runs to the ECU and KSROM is a popular ECU tuner, the assumption is it is probably a retune! We'll find out.

IMG_9754.jpg

 

This was the newest date found on the car, couldn't have been driven much longer before being parked. Tires were from 2001
IMG_9738.jpg

Cage, race seat and a pile of old harnesses

45424011_347921969097928_988580503785308

IMG_9759.jpg

 

Yikes! More vampires than a Twilight premier in here.  

IMG_9761.jpg

 

Shows how long it was in the sun, I legitimately though it was gold window covering until I lifted the wiper.

IMG_9822.jpg

All in all I would say it was a neutral experience, every unfortunate b it found was balanced by a positive bit. No worse for wear so far.

Complete list of extras discovered (for better or worse):

Momo steering wheel
Bride seat
No name Japanese made wheels
Greddy Profec boost controller
Apexi blow off valve
Buddy Club coil overs
Cusco strut tower brace

Cusco (i think) bolt in cage

KS ROM ecu
Nismo shift knob
HKS billet oil cap
Stainless exhaust
Splitfire plug wires
Blitz air filter
SARD attack meter
Yashio Factory Okachan water temp meter
Apexi power meter
ARC intercooler
Stainless brake lines

 

  • Like 1

Share this post


Link to post

If I call "shotgun" on a RHD car does that mean I get to drive?

  • Haha 1

Share this post


Link to post

Next up was working this thing in to a runner. Some basic tune-up stuff like fluids and plugs but also some other more crucial stuff like solving the low oil pressure, fixing the fuel pump properly, tires and rebuilding the brakes. Even though this thing is twenty years newer than my Datsuns, it's easy to forget that it is still nearly 30 years old itself! 27 to be exact.
It's actually closer in age to our Datsuns than it is to the Nissans of today.

First off,
The lifters in this thing sounded terrible, like an L motor that hasn't been adjusted in 3000 miles 😂 but, jokes aside quite concerning.
Unlike the S chassis SR20's, This motor is a solid lifter head, exactly the same as the VE heads. You can see my wagon build thread to see how much fun re shimming one of these heads is. Other differences include ITB's , 440cc injectors, and supposedly stronger connecting rods. Driven with a T28 like the S14. 


Basically the lifters are similar to the L motors but without the adjustment screw and so the lash pads have to be ground to the appropriate size to create the desired gap.
The leading theory was that one of these lash pads, or an entire rocker arm had flown off. I would have to yank the valve cover to investigate, of course this meant dismounting the IC and a bunch of other bracketry to get there.
I decided to start wit something simpler as I was running out of time for the day. I drained the oil, black and thin, seems that 15 years or so of degradation took it's toll. This was actually motivating as it seemed thin oil would explain the low oil pressure. 
Next, I decided to flush the system a bit by dumping some spare oil straight through and into the drain pan. Basically, just try and get as much of the old degraded oil out as possible. I had a few qaurts of 20w-50 mollasses laying around which seemed perfect to drag its way through. Poured it in new and gold, sure enough it drained out pitch black. Decided it would be good to fill it up and run it a with some other temporary oil once buttoned back up, then redrain again.

 

At this point Jeff pointed out that my pan was crushed up a bit, maybe a forklift from shipping container delivery or some really aggressive driving. 
It looked slight to me but Jeff insisted it doesn't take much to close off the oil pickup that sits just above the bottom, this would also explain the low oil press.
Seemed worth the time so I pulled it off.
IMG-9798.jpg

 

Sure enough, another great call by Jeff. There was a clear indentation in the pan from the pick up opening! Wowza. 
IMG_9797.jpg

Spent some time hammering the pan back to convex. 

But wait, whats that in the bottom of the pan..
IMG-9800.jpg

Yep, lash pads!
 

Next work day, time to dig in.

Yuck, hope that bolt grommet held up.

IMG_9786.jpg

 

Survey says? No missing rockers, or lash pads! 🤨

IMG-9788.jpg

Must have thrown a rocker at one point and then replaced it without finding the leftover bits, sheesh.
Its possible the 20W-50  was thick enough to drag them out of some hidden crevasses. 

on to clearance measuring, not easy to accomplish in and of itself.
Top number = valve number
middle = cam lode clearance
bottom = each valve clearance
IMG-9799.jpg
Not ideal as they should each be around 12 thou but, not so bad that they should make so much noise. 
Decided to keep it as is and see if the clatter was just due to old oil and low pressure. 

 

I took time bolting it back together and looked for any cracked vac lines, found a blown breather leaking oil residue and an easily cracked fuel line when replacing the fuel filter.
Actually mounted the BOV and Boost solenoid that were just zip tied to stuff.


Replaced the plugs, I got some nice NGK replacements and assumed I'd be pulling out some who knows brand or old NGK's...
IMG-9893.jpg

Nope! Thats 3 HKS plugs and 1 Nismo jobber. I didn't even know Nismo made plugs, apparently they are so rare dude could only find one though 😅 Even the HKS plugs are liek $80 a set.

I'd have almost felt bad if they were matching and weren't so roached. 

Bolted up the IC, replaced the battery and fired it up. Much better! Oil pressure making nearly 60 psi compared to the 30 before and actually rises with rpm. 
Lifter noise still present but to a much lesser degree. I have no solid lifter SR to compare to so it may even be close to normal. Good enough that I'm no longer concerned by it. 

Let it come up to temp. to try and clean out more of the old oil. Gave it some rev's all seemed good, idles well. Responds well. Time to put the final oil in.
Another surprise! Who knew MOMO made filters?
IMG-9906.jpg

 

Pulled the wheels to get new rubber, looks like the cars last day in its last life was an eventful one!
IMG-9772.jpg

Thats was most of the basic maintenace taken care of. On to more involved bits.

 

 


haha forgot to point out this gem in the last overview post, I've never seen one.
A "Power" meter, uses signals from the ECU to determine how much air/fuel is being burned and compute a live HP read out. Obviously not uber precise but it even has a function to correct it to a dyno value. Neat, if nothing else!
IMG_9753.jpg 

 

 

 

 

Edited by volkswagner
  • Like 1

Share this post


Link to post
54 minutes ago, carterb said:

If I call "shotgun" on a RHD car does that mean I get to drive?

Yep! and now you called it. No take backsies.

  • Haha 1

Share this post


Link to post
1 hour ago, carterb said:

Great work Sam!  You've been a busy boy.

Not as much as it seems, I'm just bad at posting progress in a timely manner 😅

Share this post


Link to post

Moving on. The fuel pump needed a proper replacement.
This of course involved yanking out the in tank fuel pump which inevitably gets you covered in fuel, in this case 15 year old sludge 😪

Stock unit was crusty and had a cracked pick up.

IMG-9862.jpg


I replaced it with a Walbro 255, new pick up and cleaned all the sludge out of the tank that I could reach. 
Somehow all I took was this one terrible pic. Oh well, we all know what old nasty gas and a walbro look like, use your imagination.
IMG-9861.jpg
Along with replacing a few dry rotted fuel lines, that was the fuel issue sorted, for now. I'm nervous about all the other lines that may be close to failing due to the same dry rot.

 

While I was busy sorting the mechanical bits, Jeff took it upon himself to start giving the aesthetics some love. After hours of sticker scraping, he moved on to some mudding. ☺️
IMG-0065.jpg

IMG-0182.jpg

IMG-0183.jpg

I turned focus to the suspension. The setup was assembled incorrectly and very corroded. Disassembled to clean and inspect.
Measurements suggest 675lb front springs and 500lb rear! Quite stiff to say the least.

IMG_9921.jpg

IMG-0064.jpg

I then gave the brakes some attention. Not many pic.s but here are the fronts, better off than the rears!  the rear pad material actually separated from the metal backing before separating from the rotor!
IMG-9775.jpg


As the front calipers looked on disassembly. Not too bad, cleaned them up and replaced the seals. Rear calipers got replaced entirely. 

IMG-0057.jpg

Can't slow Jeff down!
IMG-0070.jpg

IMG-0067.jpg

 

Some single stage for now.
IMG-0073.jpg

IMG-0076.jpg


Bam!
IMG-0081.jpg

 

Lets remember what that used to look like.
IMG-9735.jpg

 

 

 


 

Share this post


Link to post

To get the interior a bit more tolerable, the stock drivers seat went in and the roll cage came out.
IMG-9745.jpg

Jeff did some buffer work which made an amazing difference!
Left in progress, right untouched. 
IMG-0151.jpg

End result 😊

IMG-0154.jpg


All that was left was to turn the coils down a few inches and correct the alignment.

Then off to test drive.
IMG-0165.jpg

IMG-0164.jpg

 

All went well, so in to the daily drive routine!
IMG-0170.jpg

 

About a 100 miles in now.
A few sneaking issues. Odometer is broke, not surprising. Clutch slave leaks and needs replacement.
Only 13mpg, meaning something is causing a rich condition... have to investigate.

  • Like 1

Share this post


Link to post

Super cool car, nice job on getting back to life.

Share this post


Link to post

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

×

Important Information

By using this site, you agree to our Terms of Use.