Jump to content
]2eDeYe

620 SR20 Motor Mounts

Recommended Posts

People want s14 s15 NA s Bleach lately smooth power .

You must bolt sr and trans as one to install , recently tried a removable tunnel , to remove seat and pull trans tail shaft into cabin for a clutch job later maybe  , I think better than pulling motor and trans  and split on ground to do a clutch job ! Not new idea ,Nissan had removable tunnel /floor on early trucks ,(60-64) and Mercedes did this also.

  • Like 1

Share this post


Link to post

Anybody have more pics of the motor mounts bolted up? I’m having Trouble lining mine up. Also engine mounts I have are two diff thicknesses, so I bought multiples

Share this post


Link to post

New cross member for the 620 KA SR swap. 

 

IMG_7496.JPG

 

 

IMG_7495.JPG

 

  • Like 1

Share this post


Link to post

So with these mounts do you need to relocate the frame mounts?  Or do these compensate for the misalignment with offset?  I'd like to see more about that crossmember. Is it in production yet?

Share this post


Link to post
On 2/14/2019 at 10:55 AM, nustad620 said:

So with these mounts do you need to relocate the frame mounts?  Or do these compensate for the misalignment with offset?  I'd like to see more about that crossmember. Is it in production yet?

 

Which misalignment are you referring to?  The front to back offset of the trans mounting points?

Share this post


Link to post
On 2/14/2019 at 10:55 AM, nustad620 said:

So with these mounts do you need to relocate the frame mounts?  Or do these compensate for the misalignment with offset?  I'd like to see more about that crossmember. Is it in production yet?

 

I think it's clear this is for swapping SR and KA engine into the 620.

 

 

On 2/21/2018 at 9:49 AM, ]2eDeYe said:

Finally have a production run done. SR20DE to 620 Motor Mounts. Other than these mounts and relocating the alternator, this swap is the same as the 240SX KA24 swap. 

 

IMG_5078.JPG

 

 

The slotted trans cross member probably allows either the longer 240sx or the shorter D21 5 speed is my guess.

  • Like 2

Share this post


Link to post
On 2/14/2019 at 1:55 PM, nustad620 said:

So with these mounts do you need to relocate the frame mounts?  Or do these compensate for the misalignment with offset?  I'd like to see more about that crossmember. Is it in production yet?

 

No, bolt in.

 

It essentially allows you to run the longer KA or SR trans

I have sold a few crossmember already, will have a run through powder coat soon.

Share this post


Link to post
On 2/15/2019 at 9:56 PM, AtomChurch said:

 

Which misalignment are you referring to?  The front to back offset of the trans mounting points?

I don't know much about swapping a ka or sr into a 620,  I just started the research. But a few builds I've read the engine cross member had to be moved forward to get the new mounts to line up.  So what I was asking is are the mounts just bolt in and drop the engine in. 

Share this post


Link to post

Did you end up making a bracket for the alternator? I’ll be doing the SR swap in my 620 around this time next year, and I definitely will be purchasing your brackets and crossmember if they’re still available. 

  • Like 1

Share this post


Link to post

 

On 3/1/2019 at 4:56 PM, nustad620 said:

I don't know much about swapping a ka or sr into a 620,  I just started the research. But a few builds I've read the engine cross member had to be moved forward to get the new mounts to line up.  So what I was asking is are the mounts just bolt in and drop the engine in. 

 

Sorry I missed this, not getting notifications. grrr 
 

Well the order is more like drop the engine in place, install all of the mounts and make sure all of the bolts are started before final tightening and then dropping the engine/trans the rest of the way...

but yes, bolt in. 

 

 

12 minutes ago, SlowAndRusty said:

Did you end up making a bracket for the alternator? I’ll be doing the SR swap in my 620 around this time next year, and I definitely will be purchasing your brackets and crossmember if they’re still available. 

 

I am am about to build the first couple to test. 

 

Will do a production run if they work out. :)

 

 

3dmodel.jpg

  • Like 1

Share this post


Link to post

So how did the alternator bracket work out? Interested in a set of motor mounts and trans mount but it would be nice if i can get an alternator bracket in one go.

Share this post


Link to post

Are these still available? Would be keen on a set to a SR20 N/A Autech into a 620, all the way downunder in Australia. Cheers

Share this post


Link to post

They are available, I need to do another run. Shipping to Australia is pretty expensive. 
 

I have someone else asking for parts shipped to Aus as well, maybe I can package them together? 

Share this post


Link to post
On 9/3/2019 at 1:10 PM, Eric said:

So how did the alternator bracket work out? Interested in a set of motor mounts and trans mount but it would be nice if i can get an alternator bracket in one go.

 

I have the alternator bracket design finalized. Will be picking up the plates from the laser cutter this week. 

  • Like 1

Share this post


Link to post

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...

×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use.