Jump to content
Sign in to follow this  
Noll

Noll's '82 Lada Niva

Recommended Posts

Thanks guys! They're not perfect by any means, but should fit the bill nicely for the intended purpose.  Not sure what I'll work on next, as the majority of the body panels can't be unbolted to work on inside, but I'm sure I'll figure something out. Maybe I'll rebuild the carb or something.

 

@aibast - Yeah, they're supposed to cover a dirt trap, but seem to just keep mud trapped in there unless cleaned out regularly. Once I rebuild the rusted area on the car itself I'll be sure to clean it out consistently.

Happily the original owner undercoated the car, which has prevented a lot of rust, unfortunately it's all gooey and coming off in places now though. I'm thinking I may just bedliner the whole underside after scraping off the old stuff, am undecided as to if I want to paint bare metal under the bedliner first or not though.

  • Like 1

Share this post


Link to post

Had a nice day yesterday (+7c in feb, woo), so got some more done. All little things, but it adds up and slowly gets closer to completion.

 

Replaced the fuel filter so I can get an idea of how much sediment is in the tank, as well as if there's actually any fuel flow:

 

26676855378_46229bb4c4_b.jpg

 

 

 

Unbolted all of the front and rear tow-hooks:

 

26676854708_70457d9e8d_b.jpg

 

26676857648_93036b4451_b.jpg

 

 

Cleaned 'em up:

 

26676854108_6c00f2b78b_b.jpg

 

 

And bedliner'd:

 

26676856618_3fb16c79f8_b.jpg

 

Did the same for the engine-bay fuel vapor canister mount:

 

26676857258_23e524c21e_b.jpg

 

 

Finally also got a picture of the front skidplate I bedliner'd a few months ago:

 

26676855888_a091532336_b.jpg

 

 

Removed the rear trailer hitch too.  I'm undecided as to if i want to put it back on, as this'll never really be hauling a trailer (with that 82hp), may come in handy if I wanted to  put a bike-rack on or something though.

 

26676858268_6d074a779a_b.jpg

 

No picture of it, but happily the area where the rear valence and underside floor meet is pretty much free of anything but surface rust, so that's nice. There are a couple "pockets" right by the rear tow hook mounts that have some flaky paint/rust in them, so I'll probably sandblast up in there then brush-paint when I get to that point.

Share this post


Link to post

Had a go at starting the Niva today, as it has sat for quite some time (~10 months) since the last time I started it. A nearly-dead battery didn't do any favors, but it caught for a second with some starting fluid, and (before the batt died completely) the fuel pump got fuel up to the new filter that I had installed. No real evidence of sediment, which is nice; I'll charge the battery properly tomorrow and have another go at getting it started again then.

 

The headlights seem to have mysteriously stopped working since I last gave the car a battery too (no wiring has been touched since then), but I'm sure that's a simple fix. The rest of the lights and indicators are working flawlessly, even the dash-light brightness knob.

  • Like 1

Share this post


Link to post

Turns out the original fuel line had cracked a bit inside the fabric sheathing after I pulled it off of the old fuel filter (was leaking a LOT when I cranked the engine over), so I went to NAPA and got some new line and clamps. Much better.

 

25808340737_c3f8d6507e_b.jpg

 

26808256978_9c6ce83fe7_b.jpg

  • Like 2

Share this post


Link to post

A little more work and it is alive again :) .When I was looking for a new project car I looked @ Nivas - ended with a Vulva 740 hears, but had a tought of building dakar replica niva.

Share this post


Link to post

Yep, getting there for sure. Current to-do is brakes, clutch, rust, fluids and tires, and it'll be back on the road.

 

Yeah, I saw your thread on that, pretty cool oddball car for sure! a dakar replica niva would also be cool, might be something to consider if/when I get another niva at some point (going to keep this one pretty original).

Share this post


Link to post

Being an early Niva, mine unfortunately does not have any cupholders. I can see this being annoying, so I decided to rectify the problem myself.

 

There is a rectangular hole in the dash, where the ashtray normally goes; I don't smoke (and wouldn't in a car anyway), so I decided to start there for the cupholder creation:

 

40695583362_dae6107a79_b.jpg

 

 

 

Designed up a simple cupholder to fit in that space. this will be 3d-printed with ABS filament on my printer.

 

38928016770_16692279bc_b.jpg

 

38928016800_0d7ecb5c46_b.jpg

 

 

I'm currently printing the piece that mounts into the ashtray hole, and if that's a good friction fit like I planned, I'll print and assemble the rest. if not, I'll keep adjusting until it is.

 

I'll also make a faceplate to cover the ash tray front panel once fitment is good.

  • Like 1

Share this post


Link to post

Prototype is now printed and in place. No fitment issues, and works as it should:

 

40792315261_a08f78d5b6_b.jpg

 

25920759707_2f028efcea_b.jpg

  • Like 3

Share this post


Link to post

I have always wanted one of these cars. I bet they are harder than shit to find parts for.

Share this post


Link to post

I have always wanted one of these cars. I bet they are harder than shit to find parts for.

 Surprisingly not; I can get pretty much everything (including body parts) pretty inexpensively from ladapower.com and other europe based stores. I was expecting there to be difficulty when I first got the car, but happily not the case  B)  .

  • Like 3

Share this post


Link to post

Alright, I decided to have another go at welding, now that the weather is getting a bit better. Found a YouTube video a little while back that featured someone welding sheet metal with flux core and a re-branded version of the welder that I have, so I used his settings as a baseline for tweaking. Ended up with heat 2 (out of 4), and wire speed of 1 (of 10).

 

Started with some sheet metal I had lying around:

 

26523638567_4c8b778070_b.jpg

 

As the metal above was a little thicker gauge than what's on the Niva, I found some scraps leftover from cutting the replacement fender section to fit, and had a go at welding them to make sure I didn't burn through:

 

41394413171_114e5fcb66_b.jpg

 

Good penetration:

 

26523635047_2b2f4c37aa_b.jpg

 

 

With that test completed, I cut out a section from my replacement rocker assembly, and had a try at welding it in the car. Great Success!

 

26523641467_0e2ff52c48_b.jpg

 

Ground the welds down a bit. I'll need to go through and fix all the missed areas, but it's securely attached to the car, which makes me very happy!

 

40499209465_1ce6eeac85_b.jpg

 

Good penetration round back, despite me forgetting to clean off the undercoating. Thhere's still two areas at the ends of the panel where I'll want to add some minor patches for better fitment, as well as to remove some pitted metal at the left side.

 

40499207405_6a4f31aa4f_b.jpg

 

Obviously my welds aren't great, but they seem plenty strong, and I have a grinder. Can only really get better from here B) .

 

 

 

EDIT: and a wider angle. I still need to hammer out the side near the wheel so it lines up better before welding it.

 

26524166287_eefd84070c_b.jpg

  • Like 1

Share this post


Link to post

I made a 400km round-trip yesterday to trade a spare fender that I had for some brake parts that I needed for the niva. As I had the rebuild kits sitting around already, I got the front brakes rebuilt today, now with new (to me) casings.

 

39780550840_e07ea1a991_b.jpg

 

And back together:

 

26720401997_515cc19166_b.jpg

 

I still need to get the little pin/springs that hold the caliper brackets onto the calipers themselves, but they're otherwise ready to go back on the car. (after I clean up and paint the front suspension).

Share this post


Link to post

Did a little slicing to make the front of the panel that I welded on fit better (gotta love OEM parts not fitting right), and also fixed a couple spots where I burned through due to being a bit overzealous with the grinder after welding previously.

 

26722580517_e733931a85_b.jpg

 

I'm thinking I'll make a little piece like so to eliminate the gap, while also letting me cut out the area I filled back up with tackwelds after burning through. Luckily most of this repair panel won't be seen, so I just need strength, not prettiness.

 

26722578497_f8fde746e8_b.jpg

 

 

And to make me feel a bit better about my still crappy welds, this is some factory welding on an interior gusset (under the dash):

 

40879734764_c2894414a1_b.jpg

  • Like 2

Share this post


Link to post

Tine for another update.

 

While the exterior repair isn't done yet (need to cut/weld in a couple of sections as mentioned in the previous post), I decided to get some other parts of the repair made as I didn't feel like welding much today.

 

Started by hammering, slicing, and tacking the outer rocker repair until it was fully inline with the rest of the rocker:

 

41855719861_aae5db5eec_b.jpg

 

Cut and hammered the middle rocker section into shape:

 

41812833142_bca3310048_b.jpg

 

 

Mocked up:

41855722221_b9961ba5dc_b.jpg

 

26987537177_152f1e6ca3_b.jpg

 

and a wider angle:

 

41812831802_dc8df6f3cf_b.jpg

Share this post


Link to post

Cut up the rest of the replacement rocker panel:

 

41856817901_6624feb798_b.jpg

 

 

and test-fit:

 

40958029195_37114598b6_b.jpg

 

What it'll be replacing:

 

41139651714_23801e052d_b.jpg

 

 

Going to need to rebuild the inner rocker here at some point:

40958027815_bf7a6c9f95_b.jpg

  • Like 1

Share this post


Link to post

Decided to see how bad the pass. side floor was, so I removed the carpet and sound deadening. Looks like water got under things at some point, and the primer put under the sound deadening panels is all but gone:

 

28286626818_7ef05a974e_b.jpg

 

a bit of wire-wheeling later, this is the only spot that needs replacing (about the size of a postcard). The rest of the rust was just surface.

 

28286624908_ee33296d56_b.jpg

 

I was a bit surprised by that , as the subframe outrigger directly below the floor looks like swiss cheese:

 

28286625508_42f23866fa_b.jpg

 

28286626058_e76bb6df69_b.jpg

 

 

I will eventually get around to removing the seats and all floor interior trim to check for additional rust (despite not seeing any from the bottom), as I came across this under the sound deadening (that's the floor/trans tunnel joint); just surface for now, but I want to eradicate anything else like that before it takes hold.

 

40351971160_da777732cd_b.jpg

Share this post


Link to post

Not niva specific, but I've been doing a car restoration/metalwork course at a local college to improve my bodywork skills. Much happier with my welding skills now (done on one of the college's gas mig welders):

 

27422482147_bbfa39f19b_b.jpg

 

41390300315_0e4a4fa004_b.jpg

 

Going to bring in my flux-core welder next week to practice and get some tips. Side note, I really should get a die-grinder now, it made cleaning the above weld up so much easier.

  • Like 2

Share this post


Link to post

So, I've been a bit absent from this thread for a while, but for good reason.

 

This past summer, I circumnavigated the world, mostly by (ludicrously small) car, and got to see 25 different countries doing so.

 

It was quite a good time:

 

45430030104_2f5e3a8bd4_b.jpg

 

32282504428_67f1114262_b.jpg

 

45241673355_716bf21024_b.jpg[/url]

 

45430036994_52ee0bcf2b_b.jpg

 

In doing so, I also got to see quite a few Ladas, including an entire dealership:

 

31214535487_fd70858da8_b.jpg

 

45241659535_250b07276f_b.jpg

 

45430038134_705465c27a_b.jpg

 

45241683925_afdaff6336_b.jpg

 

Since getting back, I've been preoccupied with other projects (namely my subaru justy and a '00 Impreza OBS I got out of a ditch for 600$ as a new daily):

 

44336892740_32d8dd1b54_b.jpg

 

Now that that's all sorted for now though, I'm going to try to get back to making progress on the Niva. I've ordered some more misc bits from the Ukraine, and am hoping to make more progress on the front rust repair this week if time allows (new metal at last, with any luck).

 

 

Edited by Noll
  • Like 1

Share this post


Link to post

I like the trip pics. Good job. 

 

A friend of mine and my parts guy made a "bucket list" trip in a RAF van. From Riga  to Vladivastok.

RAF2.jpg

Share this post


Link to post
9 hours ago, Aibast said:

I like the trip pics. Good job. 

 

A friend of mine and my parts guy made a "bucket list" trip in a RAF van. From Riga  to Vladivastok.

RAF2.jpg

Thanks! It was one hell of an adventure.

 

That's quite the journey as well! I actually ended up in Vladivostok for a day after taking the train from Ulan Ude  (and from vlad, 4 flights to get home to canada). Pretty cool city!

Share this post


Link to post

That Lada front wing window looks [without measurements] to be a possible replacement for the Datsun 410 and 411 units.  Not surprising since both vehicles have distant descent from Pinin Farina designs.

Share this post


Link to post
4 hours ago, MikeRL411 said:

That Lada front wing window looks [without measurements] to be a possible replacement for the Datsun 410 and 411 units.  Not surprising since both vehicles have distant descent from Pinin Farina designs.

It's possible! The 2101's (white and green cars in my above pics) are based off a fiat 125, and I believe the doors are interchangeable.

Share this post


Link to post

Alright, little update for today. Cut out part of the front rocker that I've been meaning to replace for a while, and test-fit the replacement part in place. Just need to weld this in and fix the burn-thru on the front edge of this panel, and then I can move on to putting the rest of that corner back together (center section, floor, inner rocker, subframe outrigger, fender section).

 

46130091762_ff45f9d226_b.jpg

Share this post


Link to post

I went out to the garage to tack the new piece in, and ended up welding up that rocker entirely. Pretty happy with my progress! My welding skills are still nothing fancy, but I'm miles better than the last time I tried to weld on this part of the car.

 

32311215698_02a2912cf9_b.jpg

 

44365948010_230ab561d7_b.jpg

 

32311214808_1630c063e6_b.jpg

 

Should need very minimal work to be ready for actual paint, especially as I'll be bedlinering the lower rockers. I didn't bother cleaning up the bits that will be hidden as much.

 

 

 

 

 

46185325231_f2272f90a1_b.jpg

 

Next up will be to fit and weld in the rocker strengthening piece, then the floor and inner rocker.

Edited by Noll

Share this post


Link to post

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
Sign in to follow this  

×

Important Information

By using this site, you agree to our Terms of Use.