Jump to content

E-16/E-15


Grahem

Recommended Posts

has anyone ever tried swapping E-15 and E-16 engines? I have a 92 Nissan sentra classic with a blown head-gasket and an 82 datsun 310 with a rebuilt head/new head-gasket. Can i swap the E-15 in place of the E-16? I`m hoping i can bolt all the E-16 parts to the E-15 to keep the throttle body injection. Thanks

Link to post
  • Replies 21
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

You're the first person to mention it since I've been a Ratsun member.

 

I love the E motors. They have massive HP potential, due to the cylinder head, port design. I've built them to run in SCCA GT and DSR classes and even a few for the street. With dual 44's (or ITB's), they really scream.

 

But...

 

Mounting them in a longitudinal position, you're going to have to come up with a solution for the distributor. Either a distributor relocation, some sort of electronic ignition, or cut a deep recess in your firewall.

 

Body mods are probably the easiest route, but also the quickest route to destroying a good car. I had to relieve the firewall in my dad's Sunbeam Alpine to make room for the 4AGE-20V Blacktop I put in it, but I think I did a good job. If you have sheetmetal welding skills, this is a piece of cake. If not...find someone that does.

 

IMG_5542_zpsiunyi44g.jpg

 

IMG_5541_zpsow4rfwr6.jpg

 

IMG_5545_zpshxjj5ifu.jpg

 

IMG_5548_zpsp8ya0ttn.jpg

Link to post

I do believe it can be done. I've have the remnants of A/E engine hybrid ( E15 turbo cylinder head mounted on A14 block) that was used in SCCA D sports racers before everyone went to bike motors (once upon a time I ran a Yamaha DSR). I seem to recall talk about the E-Series being interchangeable. Parts couldn't mixed and matched to get anything between 1300cc to 1700cc.

 

Check on the Pulsar forums from Australia and New Zealand but I know there where some old posts on there that would answer your questions.

 

Tom

Link to post

Again down to memory but the E Series was an update to the A Series (hence the E head bolting on) the GA was an update on the E series; somewhere on Datsun1200.com there is a post about swapping bellhousings to swap GAs into older FWD cars.

Link to post
  • 1 month later...

Well it lasted 3 or 4 weeks before it shit the bed so I am now half way thru swapping the Japan built E-15 in place of the Mexican E-16. Only the block head and thermostat/distributor mont are the same everything else has been swapped onto the E-15 from the E-16. Hopefully it fires up and runs ok once it's reinstalled

Link to post

Ya everyone like pics lol. The engine is in and mostly hooked up but I broke one of the cv c clips so I won't be able to complete the swap until sunday

  • Like 1
Link to post

c%20clip_zpsqchwpb70.jpg

the clip that screwed me 

 

sentra%203_zpsenjoh7do.jpg

all installed, got it fired up tonight seems to run well just have to figure out how to time it and maybe adjust the valves.

Link to post

They seem to go thru head gaskets but other wise are good little engines. For the record it almost fits the valve covers have different predrilled holes so only on of the air cleaner bolts lines up and the coolant return spout is different which required an inline tee for the heater connection

Link to post

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...
×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use.