mrbigtanker Posted February 13, 2019 Author Report Share Posted February 13, 2019 Header has bung in it and now at Cermaic coat shop. 1 Quote Link to comment
Tedman Posted February 13, 2019 Report Share Posted February 13, 2019 Stock NA 280ZX are flat tops, 86mm bore, same pin height as L20B. ~ 10.5:1 with peanut head, even higher with that 210 head you have there. Better to use a U67 L20B head if you want to run safely on pump gas. 2 Quote Link to comment
mrbigtanker Posted February 13, 2019 Author Report Share Posted February 13, 2019 10 minutes ago, Tedman said: Stock NA 280ZX are flat tops, 86mm bore, same pin height as L20B. ~ 10.5:1 with peanut head, even higher with that 210 head you have there. Better to use a U67 L20B head if you want to run safely on pump gas. The head I have is all tricked out. Lesson after 1500.00. Lol. But getting ported to 38 mm. So I am sure it will be good. Do you have a flywheel for L20. 1 Quote Link to comment
Tedman Posted February 13, 2019 Report Share Posted February 13, 2019 46 minutes ago, mrbigtanker said: Do you have a flywheel for L20. Yeah, I have a stock cast iron Z flywheel that fits an L20B. Takes a 225mm clutch. Weighs ~22 lbs vs. closer to 30 for a stock L20B one. PM me if interested. 1 Quote Link to comment
mrbigtanker Posted February 14, 2019 Author Report Share Posted February 14, 2019 On 2/12/2019 at 9:26 PM, Tedman said: Yeah, I have a stock cast iron Z flywheel that fits an L20B. Takes a 225mm clutch. Weighs ~22 lbs vs. closer to 30 for a stock L20B one. PM me if interested. Thank you sir for the Flywheel. 1 Quote Link to comment
mrbigtanker Posted February 17, 2019 Author Report Share Posted February 17, 2019 (edited) Untitled by raymond medeiros, on Flickr Untitled by raymond medeiros, on Flickr Untitled by raymond medeiros, on Flickr Untitled by raymond medeiros, on Flickr Just some parts for the new build. Edited March 9, 2019 by mrbigtanker 2 Quote Link to comment
mrbigtanker Posted February 17, 2019 Author Report Share Posted February 17, 2019 (edited) Untitled by raymond medeiros, on Flickr Untitled by raymond medeiros, on Flickr Just need a clutch. I will wait a bit before I buy one. Edited March 9, 2019 by mrbigtanker 2 Quote Link to comment
mrbigtanker Posted February 17, 2019 Author Report Share Posted February 17, 2019 By the way the pistons are 40 over. 2 Quote Link to comment
thisismatt Posted February 17, 2019 Report Share Posted February 17, 2019 Ray, when are you gonna start spending some money on this project? ? 3 Quote Link to comment
mrbigtanker Posted February 17, 2019 Author Report Share Posted February 17, 2019 2 hours ago, thisismatt said: Ray, when are you gonna start spending some money on this project? ? Soon real soon. Waiting for tax returns. Wait never mind I pay for some odd reason. Lol 2 Quote Link to comment
thisismatt Posted February 17, 2019 Report Share Posted February 17, 2019 Better that way, unless you spend all your extra money on Datsuns, then it's lose-lose... 3 Quote Link to comment
Duncan Posted February 18, 2019 Report Share Posted February 18, 2019 (edited) Hey look! You got a camber plate for your motor! ? And damn it, Mr Big! I've been looking at those Work Meister wheels for a while now, and realized you have a set on your wagon. Back to the drawing board.. Edited February 18, 2019 by Duncan 3 Quote Link to comment
mrbigtanker Posted February 26, 2019 Author Report Share Posted February 26, 2019 (edited) Untitled by raymond medeiros, on Flickr Extra one. Edited March 9, 2019 by mrbigtanker 4 Quote Link to comment
mrbigtanker Posted March 9, 2019 Author Report Share Posted March 9, 2019 Untitled by raymond medeiros, on Flickr Untitled by raymond medeiros, on Flickr No re pops here. Thanks Jimmy. 3 Quote Link to comment
edekalil Posted March 13, 2019 Report Share Posted March 13, 2019 I've been thinking about it and figure you could just send all that stuff over here and I'll put it on the 70 510. 2 Quote Link to comment
mrbigtanker Posted March 13, 2019 Author Report Share Posted March 13, 2019 2 hours ago, edekalil said: I've been thinking about it and figure you could just send all that stuff over here and I'll put it on the 70 510. Or you just send the 2 door to me. 2 Quote Link to comment
edekalil Posted March 13, 2019 Report Share Posted March 13, 2019 2 hours ago, mrbigtanker said: Or you just send the 2 door to me. Excellent response 👍. 2 Quote Link to comment
mrbigtanker Posted March 17, 2019 Author Report Share Posted March 17, 2019 Or I get a bluebird. Hint hint wink wink 2 Quote Link to comment
edekalil Posted March 17, 2019 Report Share Posted March 17, 2019 8 hours ago, mrbigtanker said: Or I get a bluebird. Hint hint wink wink Excellent idea. I was very tempted to get a 4 door Bluebird someone had for sell a couple of years ago. I just have no room. You want a 64 Formula S Cuda with a wacked out 340 in it. I need some room in the garage. 2 Quote Link to comment
iceman510 Posted March 18, 2019 Report Share Posted March 18, 2019 On 2/17/2019 at 1:47 AM, mrbigtanker said: Just some parts for the new build. What's the dish on those pistons, and what CR are you aiming for? Maybe you showed the head already, but many of the earlier pictures are not showing up. Thanks. 1 Quote Link to comment
mrbigtanker Posted March 19, 2019 Author Report Share Posted March 19, 2019 7 hours ago, iceman510 said: What's the dish on those pistons, and what CR are you aiming for? Maybe you showed the head already, but many of the earlier pictures are not showing up. Thanks. Give me some time and I will try to get you a part number. Also I'm not sure on compression ratio. 1 Quote Link to comment
mrbigtanker Posted March 19, 2019 Author Report Share Posted March 19, 2019 On 3/8/2019 at 6:08 PM, mrbigtanker said: Untitled by raymond medeiros, on Flickr Untitled by raymond medeiros, on Flickr No re pops here. Thanks Jimmy. this is all stripped and and powder coat shop and chrome shop, it will be nice. Now I need to find a car to put it on. 2 Quote Link to comment
thisismatt Posted March 19, 2019 Report Share Posted March 19, 2019 Brah, why you no let me sneak some parts in on your chroming batches? 2 Quote Link to comment
Draker Posted March 19, 2019 Report Share Posted March 19, 2019 3 hours ago, mrbigtanker said: this is all stripped and and powder coat shop and chrome shop, it will be nice. Now I need to find a car to put it on. Great buy there, glad to see it go to a good home. 2 Quote Link to comment
mrbigtanker Posted March 23, 2019 Author Report Share Posted March 23, 2019 Untitled by raymond medeiros, on Flickr Just need to paint and then start to assemble. .40 over L20 2 Quote Link to comment
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.