Jump to content

heater hoses


mntnman

Recommended Posts

Posted

does it matter which hose goes where off my heater core to the engine, l20b engine in a 71 510, and do you have a pic or diagram

  • Replies 10
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted

The one from the head should go the the heater cock and the other is the return. But in reality, both will work. It's like turning a sandwich upside down and finding it tastes the same.

  • Like 1
Posted

You have presumably a 42 year old heater core.  If you plumb the intake hose to the inlet valve and then shut it off the heater core is not pressurized.  If you plumb the intake hose to the outlet then whatever you do the old core is pressurized and just waiting to find a weak solder joint,  The choice is yours [got a whole roll of paper towels just in case?]

Posted

Heater hoses in the engine compartment are still available from Nissan

B7020-A0800

0c9b8851.jpg

B7021-A0800

42300e35.jpg

Posted

the S shaped hose is a perfect fit also in the inside passenger to the heater core. just cut the end off. as I could never find the correct part number for that part and the part store guy at Nissan would have a hard time finding the number, well never did find the part number

Posted

You have presumably a 42 year old heater core.  If you plumb the intake hose to the inlet valve and then shut it off the heater core is not pressurized.  If you plumb the intake hose to the outlet then whatever you do the old core is pressurized and just waiting to find a weak solder joint,  The choice is yours [got a whole roll of paper towels just in case?]

.

 

Wait a minute, wait a minute. The pressure is the same in every part of the cooling system. Think about it.... if the head is under pressure then the block has to be too. Even if the thermostat is closed any pressure in the block is also in the water pump and the lower rad hose and at the same time all of the rad and the return line from the heater core. They are all connected and all under the same pressure. 

Posted

.

 

Wait a minute, wait a minute. The pressure is the same in every part of the cooling system. Think about it.... if the head is under pressure then the block has to be too. Even if the thermostat is closed any pressure in the block is also in the water pump and the lower rad hose and at the same time all of the rad and the return line from the heater core. They are all connected and all under the same pressure.

 

 

If that were true then no coolant would flow through the heater core.  Remember, the water pump impeller adds pressure to the liquid or else nothing would flow except by convection like the original Fords which had no water pump.

Posted

I was thinking the normal pressure for being hot, like up to 13 lbs that the rad cap is rated for. Hmmmm I wouldn't think that much pressure from the pump. Well better safe than sorry I guess.

Posted

There's a pressure differential, but not much.  The lowest pressure MIGHT be at the inlet of the water pump, but more likely it's the top of the radiator tank in a Datsun.  Highest pressure is inside the head, due to heating.  When the water is cold and of uniform temperature (which isn't long once the engine starts) the highest pressure is at the outlet of the water pump, but that's far less than the pressures created by heating.  The differences in pressure are very low throughout the system.

 

In reality a pumpless, convection loop system would work, just like the original Model Ts.  You just need a far more efficient plumbing system than the Datsuns have, and absolutely NO air pockets.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...
×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use.