Jump to content

zetabird

Members
  • Posts

    26
  • Joined

  • Last visited

Everything posted by zetabird

  1. Nope no gasket thats why i thought it was pipe thread. ive got it back on without the filter in it. It was crushed.
  2. Nope its a 90 degree hose barb that had a small meah screen in it but that was smashed when i took it off it looks like pipe thread to me but i dont k ow if japan would have used a diffrent standard than we did on that
  3. another question instead of cloggin it up with a new thread, the fuel inlet fitting on the carb is a bit bent and buggered up from a previous "rebuild". do you know if its a standered pipe thread or is it some type of metric. the shop i work at has boxes of AN fittings and enough scraps of line from the racecars that i can build a whole new fuel system with scraps for free.
  4. alright, will do i was just going to do center out tightening them,. never messed with anything that uses these yoke washer before though.
  5. been doing alittle digging and was just looking for a solid answer, im putting the intake and exhaust back on and need the torque spec and sequence. from what ive read it should be about 10-14 ft/lbs is that right?
  6. that was my plan b, looks like il just go that route. thanks.
  7. zetabird

    egr mount gasket

    im in the process of fixing some intake and exhaust leaks and rebuilding the carb, looks like the last gasket i need is the on that goes between the egr adapter and the intake, its on a 78 B210... i have not been able to find a part number,
  8. zetabird

    new here

    got a chance to test fit the wheel. once i get the rust cut out and the flares on, along with lowering the car its should look far better. what blocks do you use on the rear.
  9. zetabird

    new here

    got the wheel last night, mounted it this morning.
  10. huh didnt find this thread when i was looking into the same wheels for mine... my rear arches are rough so its getting flared anyway. did you get the lugnuts that go with the wheels? from what basset told me you have to have a nut with a 45 degree chamfer instead of 60 like most nuts are.
  11. zetabird

    new here

    i also got my new new tires and i have one wheel ordered for now, fender flares are on order aswell. just gotta see where im going to cut for the tires and flares
  12. zetabird

    new here

    im going to have to take it all back a part to see whats going on. i had removed the center pivot because the plastic mount broke and i bolted the linkage together. the driver side are had mostly normal travel now it needs to go like 4 more inches... im not sure how i messed it up
  13. zetabird

    new here

    i got the wiper pivot back on... now the drivers wiper arm dosent seam to go up far enough, dose anyone here know weather the linkage that goes from the driver to passenger arm go ontop of the passenger side pivot or the bottom?
  14. ill check that, i need to get it back into work so i can get under it anyway and change the fluid in the trans. got two of my new tires just need to order a wheel so i can get it fitted and see where i have to trim the wheel arch for the flares.
  15. ill have to check. that, im not sure. ive only been under it to rig some exhaust on it.... the front of the pipe broke off and fell whe the PO was driveing and rolled the entire exhaust up into a ball.....
  16. thats what i was thinking, thanks, ill proly do that over next winter if the one lasts that long
  17. looks like at some point i am going to have to replace my clutch, are there any option other than a stock like replacement. i can get a kit from napa for faily cheap
  18. zetabird

    new here

    time to try to fix my broken wiper arm mount. i have it rigged to work on ly the driver arm right now. gotta finish this bracket to remount the passenger side
  19. hmm its something to look into insted of rebuilding or buying a new stock carb, thanks
  20. So it looks like i should find a set of R1 carbs. R1 as in off of a Yamaha R1? with the stuff i have at the shop the intake should be really easy to fab up
  21. zetabird

    new here

    yeah one of the guys thought i added machine guns to the car.... i cant lie and say i didnt consider it. once i get some free time i have a hood scoop and chin spoiler to put on.
  22. zetabird

    new here

    cool that did work, this is before i took the bumper mounts off and painted that all black. and before i took the hubcaps back off.
  23. zetabird

    new here

    ill try that, thanks.
  24. zetabird

    new here

    yeah i hate links to, how do you put the image in the post, i was trying to figure it out... im prolly just missing it. i have some sheet metal to fix the lower quarters when it warms up out . also want to lower it throw some bolt on flares on it and get a set of 15 inch areo wheels, the shop i work at on the weekends is a vendor and hes ordering me a set.
×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use.