Jump to content

Kingcab

Members
  • Content Count

    122
  • Joined

  • Last visited

Everything posted by Kingcab

  1. The dead spots at low rpms high rpms it does fine. What would i need to regap the plugs to and I'm 12° on cam and at 12 mark on dizzy
  2. I just put on dual 40mm side draft webbers and it idles just fine but I cannot figure out why it has dead spots and hesitation can anyone help please
  3. So I just installed some used 40mm side draft carbs on my l20b motor it idles fine but is has a huge hesitation any one know how to possibly fix this?
  4. What metal are the stock knuckles made of on 720? I'm trying to figure out what I need to chop n weld em for more steering angle and not sure if made from cast iron or cast steel or posably other metals
  5. Why would I cut the metal liner on the w58 exactly? And what's the difference in the square ports vs round ports.
  6. I've red up on alot of different builds with these 2 motors. I have a l20b I'm running right now with 1mm over bore and a w58 stock head. I have 2 z22 motors sitting here one out of a 83 720 other one out of an 83 200sx. I was wondering if I could use the pistons cranks and rods for a build that would be worth it with any combination of what I have laying around. It's a daily driver/ drift motor so I'm looking for more horses and reliability but I'm not scared to tear into any of it
  7. I got a used w58 head for my l20b and rebuilt it right before I was going to install it i realised there was no freeze plugs right where the headers bolt on to the head. I was wo dering where I could find new ones or what I could psably do for cheap fixx
  8. Kingcab

    Chevy 4.3 into my 720

    Thanks for the info I will get back to all of you once I figure more out
  9. Kingcab

    Chevy 4.3 into my 720

    I would much rather a ka but this motor and parts are free to me. And it doesn't seem to hard to swap into 720 until I find a ka
  10. Kingcab

    Chevy 4.3 into my 720

    Is there an oil pan I could bolt on for better clearance? Also would I need to mod the driveline?
  11. Kingcab

    Chevy 4.3 into my 720

    It's not a 4x4 and I'm going find a manual trans for it. And possible carb swap.
  12. So I'm getting this 4.3 motor from a 92 chevey s10 for free also getting the wire harnes driveline and rear end. I was wondering what it would take to swap it into my 720. I've been doing a little bit of research but cant find out exactly what I would need and how it fits. Any info helps
  13. I have a w58 peanut head stock on my l20b whatt other heads come stock on l20b and what one would be best to use?
  14. What all would I need for the swap? Driveline rear end?
  15. Okay I'll look into that I know someone with parts I can get for ka24 de
  16. Again just trying to get ideas on what I want to do... what would you recommend swapping into the 720 for an easy ish fit with more horses As this is my drift truck build
  17. I'd also like to see what ot would take to swap a l28 into the 720 and of it would be worth the time and build
  18. I know I sounds like a dummy asking all these questions but I'm just trying to figure out what kind of a build I want to do. I really appreciate all your feedbacm!!
  19. Could I bolt on the camshaft from the l20b and put it in the z head?
  20. I'm thinking about putting a z22 head and front on the l20b... any thoughts?...
  21. I rebuilt the bottom end about 4000 miles ago.. I bored out 1mm bigger than factory.. I put bran new pistons crank bearings front and rear main seals, oil pan seal front cover seal and head gasket also all coolant and oil pump gasket. As we all as tranmiston seals.
  22. Its leaks oil badly from the front cover and I have replaced the gasket multiple times.
  23. Sorry to be all over the place but the headlight issue was a loos terminal. But the dash light and cig lighter still dont workk
  24. I resurfaced the head with a flat board and sand paper I was wondering if it would be more worth it to do the same to the front cover.. as it has the studs in it and not sure if there removable for the process...
  25. Thays really good info to have! Thanks! ... i think my l20b front cover is worped is why I'm asking about this. Would it be easier/more affective to just resurface the l20b front cover?
×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use.