Jump to content

Kingcab

Members
  • Content count

    70
  • Joined

  • Last visited

Community Reputation

19 OK

About Kingcab

  • Rank
    Member

Profile Information

  • Location
    Roseburg Oregon
  • Cars
    Datsun 720
  • Interests
    Building my datsun
  1. Kingcab

    720 with 83 200sx rear end

    I also have the hard body drop spindles in front and well as the rotors calipers and steering rack. If I can find right rear end and diff it should drift perfectly from what I'm looking at.
  2. Kingcab

    720 with 83 200sx rear end

    It makes a big difference sliding smoothly without the hop and left to right movement while sideways. As I would assume you already know more than I could think of lol. I'm kinda a dumyy and just learning the proper parts to use. But If I'm piontes the proper detection i can fab all the metals needed for the swap.
  3. Kingcab

    720 with 83 200sx rear end

    I'm really trying to go 4 link cuz when I drift the rear end bounces so and insane amount I already got the lowering leave springs for the d21 and moded them to fit my 720 and it still hops way to much! If I can find a good cheap 4 link rear end I will do what it takes to fab it in. And idk what you mean by "just drifting" but the rear end moves a lot when sliding I'm trying to get as little movement side to side as well as hoping up n down.
  4. Kingcab

    720 with 83 200sx rear end

    Okay so I'm not gunna even try them. Thanks for all the helpful info guys! I'm just gunna try to save up n find a d21 rear end
  5. Kingcab

    720 with 83 200sx rear end

    Hahaha. There nothing wrong I'm just seeing if maybe I could put this 4 link rear end on my 720. Like I said it's just sitting there so maybe I could use its parts for a poor man's drift build. I have a welder I have time I have plenty of scrap mettle to use I also have a shop with all tools needed for this project.i already c notched for 3 inches of clearance.and I also have a few 4 lug wheels I really want to use I'm just trying to see if maybe someone had some good advice on what exactly i would be getting myself into. (It's a poor mans drift truck build)
  6. Kingcab

    720 with 83 200sx rear end

    Also with the 4 lug pattern,I was wondering what it would take to make the front lug pattern the same.
  7. Kingcab

    720 with 83 200sx rear end

    Well I dont have cash to buy a rear end and I have a 200sx sitting here. I was trying to see if maybe I could use the pre existing 4 link set up and just fab mounts to my frame.
  8. Kingcab

    720 with 83 200sx rear end

    Was wondering what kind of fab I would need to do for the 200sx 4 link rear end put in my 720 datsun. Also if anyone knows the width of the 200sx rear end
  9. Kingcab

    720 bed

    Will the nissan hardbody bed bolt onto the 82 datsun 720??
  10. Kingcab

    High steering angle knuckles

    It was the same sight as posted above. I actually got an email back stating they where the 2 piece bolt on knuckles.
  11. Kingcab

    High steering angle knuckles

    I seen this sight. But they have no picks of there knuckles and I don't know if they are selling just the knuckles for 2 piece spindles or if it's the 1 piece spindles? Also has anyone on here purchased these? (Picks and details on then??)
  12. Kingcab

    83 200sx

    The coils wires and plugs are new** could this be the dizzy??
  13. Kingcab

    83 200sx

    The spark is the problem after it dies.thers also need coils wires and plugs
  14. Kingcab

    83 200sx

    Okay guys. So my 200sx has a problem.. It starts right up and it will idle and rev for about 1 minute tops. ( the Reeves are really ruff and spuddery) Then it dies and won't start for about a half hour. I've checked all fuses. One thing I noticed was the ECU has a green light on it that will flash one time then the light turns off. There is no check ingine light on either. Also I've replaced all bad vacuum lines.. Anyone have info on what could be wrong with it??
  15. Kingcab

    High steering angle knuckles

    Was wondering If any company out there sells modified one piece spindles (steering knuckles) for high steering angle.. I'm asking for the 1 piece spindles cuz I updated my calipers rotors yo the 98 hardbody parts. And know the stock 720 spindles are 2 piece(bolt on knuckles).
×

Important Information

By using this site, you agree to our Terms of Use.