Jump to content

jser12

Senior Member
  • Posts

    602
  • Joined

  • Last visited

Everything posted by jser12

  1. By the way, I sold this. Peace out guys. Hopefully I'll see you again someday.
  2. I have a book at home in the basement that will teach you everything you need to know about them. Since you are my brother, it can be yours in exchange for a 6 pack of beer
  3. car is still for sale

    1. r0p0doe

      r0p0doe

      Ill give yah a dollar...

    2. I'm BLUE

      I'm BLUE

      Quitter trolol. Also your ad probably expired unless this is a trolling line then well done sir.

    3. pondking
  4. Oh, I wanna play too Pair of Bridgestone potenza wheels. 15x6.5 +12
  5. Pretty sure I'm gonna sell. Not sure when yet. Definitely by September
  6. The old Konig Rewinds were 14x7 -9 and those required a small bit of fender roll.
  7. it might be time to get out of the datsun game...

    1. laotsu

      laotsu

      I agree, send me all your rare parts

    2. Raggleflaggle
    3. skyblue

      skyblue

      never say die!

  8. if any one sees any 510 shells for sale on the east coast, let me know. it would be cheaper for me to buy one and swap all my parts into it rather than fixing the gapping holes in my current 71. i'm willing to drive.
  9. so stevexc should definitely sell me a pair of wheels for my dime.... hint hint
  10. seems like a great starting point. i'll be watching this to see where it goes.
  11. Tension control rods installed. Handles pretty nice. Lost half my rocker panel on the interstate today. Now is when I start to worry about rust repair over anything else.
  12. ugliest thing I have ever seen. it doesn't deserve to share the same driveway as my 510 haha
  13. I would say the rear has about 4-5 inches of travel but it isn't all used. The 200lb springs hold up fairly well in such a light car. And the rear end seems fine for the street abuse I put it through and the corners it tackles. I just need to slot the rear crossmember to adjust for toe and camber I like it, it's a good setup for the money on a budget build.
  14. I do on ramps at 70+ mph without any give from the rear. The shock is as high as I could turn it before putting the car back on the ground. I'm tucking half the tire on a 195/60 which isn't so bad. I'm thinking of ways to try to raise up the rear just a bit to get a little more clearance. The rear is about 5.5" above the ground. Enough to clear plenty of things.
  15. The shock is a lot shorter. These are the top hats I am using https://technotoytuning.com/nissan/510/conical-upper-hats-coilovers-25-id-springs This is the ride hieght. Note, this is full height. It's not bad, handles pretty good. And these are the shiny parts installed Hope this helps
  16. I've been driving my car a lot lately to work (45 mins each way) into Detroit of all places. really sticks out surrounded by Camaros and Mustangs. just ordered Techno Toy Tuning TC rods and I hope to install those soon. I forgot that I owned a spare rear cross member, I'll probably sand blast it, paint it purple, slot it and then slap it in my car. if the slotting doesn't goes as planned than I will probably order Byron's brackets. just want to give it a shot to see how it goes. that's all I have for now. PEACE :thumbup:
  17. I have 250 in the front and 200 in the rears. Handles good. Not to hard, not to soft. I like the ride.
  18. That dash is unsettling. Best of luck at canby 2017
  19. My datsun in Detroit taken after work.
×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use.